Imbedded Internet Course

For general Flowcode discussion that does not belong in the other sections.
steve001
Valued Contributor
Posts: 185
http://meble-kuchenne.info.pl
Joined: Wed Jan 13, 2021 7:15 pm
Has thanked: 81 times
Been thanked: 30 times

Imbedded Internet Course

Post by steve001 »

Afternoon All,

Downloaded this module and started to read through the content. It talked of a CD with all the examples on it. Can this be downloaded anywhere ?

Regards

Steve

chipfryer27
Valued Contributor
Posts: 1110
Joined: Thu Dec 03, 2020 10:57 am
Has thanked: 278 times
Been thanked: 397 times

Re: Imbedded Internet Course

Post by chipfryer27 »

Hi

No link or attachment <s>

Regards

steve001
Valued Contributor
Posts: 185
Joined: Wed Jan 13, 2021 7:15 pm
Has thanked: 81 times
Been thanked: 30 times

Re: Imbedded Internet Course

Post by steve001 »

That's what i am asking .. Can the example files be downloaded ?
The course content describes a supplied CD

Steve

Steve-Matrix
Matrix Staff
Posts: 1234
Joined: Sat Dec 05, 2020 10:32 am
Has thanked: 167 times
Been thanked: 277 times

Re: Imbedded Internet Course

Post by Steve-Matrix »

steve001 wrote:
Sun Jan 16, 2022 5:04 pm
Downloaded this module and started to read through the content
Hi Steve - which module are you referring to? Do you mean the Embedded Internet course on this page?

https://www.flowcode.co.uk/education/

I have asked my colleagues if these are available and will let you know...

Steve-Matrix
Matrix Staff
Posts: 1234
Joined: Sat Dec 05, 2020 10:32 am
Has thanked: 167 times
Been thanked: 277 times

Re: Imbedded Internet Course

Post by Steve-Matrix »

The Embedded Internet course files can be found here:

https://www.matrixtsl.com/eblocks/resources/

steve001
Valued Contributor
Posts: 185
Joined: Wed Jan 13, 2021 7:15 pm
Has thanked: 81 times
Been thanked: 30 times

Re: Imbedded Internet Course

Post by steve001 »

Hi Steve

Yes thats the one, thank you

Steve

steve001
Valued Contributor
Posts: 185
Joined: Wed Jan 13, 2021 7:15 pm
Has thanked: 81 times
Been thanked: 30 times

Re: Imbedded Internet Course

Post by steve001 »

Morning All,

I am Looking at using a couple of ECIO 40p's / 28p's & ENC28J60 breakout boards to experiment and do the examples with.
Am i likely to experience any issues / run into problems with these ?

https://hobbycomponents.com/wired-wirel ... ork-module

Steve

LeighM
Valued Contributor
Posts: 394
Joined: Mon Dec 07, 2020 1:00 pm
Has thanked: 69 times
Been thanked: 208 times

Re: Imbedded Internet Course

Post by LeighM »

Hi Steve,
The Matrix Embedded Internet course and examples use the W5500 (WIZ Click board) so you will likely find it easier if you use the same.
The ENC28J60 is cheaper, but needs more software to drive it.
Hope that helps
Leigh

steve001
Valued Contributor
Posts: 185
Joined: Wed Jan 13, 2021 7:15 pm
Has thanked: 81 times
Been thanked: 30 times

Re: Imbedded Internet Course

Post by steve001 »

Thanks Leigh, will the ECIO's be ok also ?

Steve

LeighM
Valued Contributor
Posts: 394
Joined: Mon Dec 07, 2020 1:00 pm
Has thanked: 69 times
Been thanked: 208 times

Re: Imbedded Internet Course

Post by LeighM »

Yes, should be.
The W5500 modules connect to the processor via SPI.

Post Reply