[Device]
Pins=40
Ports=5
ADCPins=9
ADCBits=10
MaxClock=40000000
PrescalerBits=3
ClockDivider=4
TimerOverflow=256
ConfigAddress=0x300000
ConfigCount=14
PWMCount=2
EepromSize=256
HasAltPWM=0
Pwm2IsD4=0
FlowcodeProduct=PIC
DefaultPackageType=0

[Pins]
Pin1 = "MCLR/VPP/RE3"
Pin2 = "RA0/AN0"
Pin3 = "RA1/AN1"
Pin4 = "RA2/AN2/VREF-/CAP1/INDX"
Pin5 = "RA3/AN3/VREF+/CAP2/QEA"
Pin6 = "RA4/AN4/CAP3/QEB"
Pin7 = "RA5/AN5/LVDIN"
Pin8 = "RE0/AN6"
Pin9 = "RE1/AN7"
Pin10 = "RE2/AN8"
Pin11 = "AVDD"
Pin12 = "AVSS"
Pin13 = "OSC1/CLKI/RA7"
Pin14 = "OSC2/CLKO/RA6"
Pin15 = "RC0/T1OSO/T1CKI"
Pin16 = "RC1/T1OSI/CCP2/FLTA"
Pin17 = "RC2/CCP1/FLTB"
Pin18 = "RC3/T0CKI/T5CKI/INT0"
Pin19 = "RD0/T0CKI/T5CKI"
Pin20 = "RD1/SDO"
Pin21 = "RD2/SDI/SDA"
Pin22 = "RD3/SCK/SCL"
Pin23 = "RC4/INT1/SDI/SDA"
Pin24 = "RC5/INT2/SCK/SC"
Pin25 = "RC6/TX/CK/SS"
Pin26 = "RC7/RX/DT/SDO"
Pin27 = "RD4/FLTA"
Pin28 = "RD5/PWM4"
Pin29 = "RD6/PWM6"
Pin30 = "RD7/PWM7"
Pin31 = "VSS"
Pin32 = "VDD"
Pin33 = "RB0/PWM0"
Pin34 = "RB1/PWM1"
Pin35 = "RB2/PWM2"
Pin36 = "RB3/PWM3"
Pin37 = "RB4/KBI0/PWM5"
Pin38 = "RB5/KBI1/PWM4/PGM"
Pin39 = "RB6/KBI2/PGC"
Pin40 = "RB7/KBI3/PGD"

[Ports]
PortPin1=0x0403
PortPin2=0x0000
PortPin3=0x0001
PortPin4=0x0002
PortPin5=0x0003
PortPin6=0x0004
PortPin7=0x0005
PortPin8=0x0400
PortPin9=0x0401
PortPin10=0x0402
PortPin13=0x0007
PortPin14=0x0006
PortPin15=0x0200
PortPin16=0x0201
PortPin17=0x0202
PortPin18=0x0203
PortPin19=0x0300
PortPin20=0x0301
PortPin21=0x0302
PortPin22=0x0303
PortPin23=0x0204
PortPin24=0x0205
PortPin25=0x0206
PortPin26=0x0207
PortPin27=0x0304
PortPin28=0x0305
PortPin29=0x0306
PortPin30=0x0307
PortPin33=0x0100
PortPin34=0x0101
PortPin35=0x0102
PortPin36=0x0103
PortPin37=0x0104
PortPin38=0x0105
PortPin39=0x0106
PortPin40=0x0107

[PortMasks]
PortMask0=0xFF
PortMask1=0xFF
PortMask2=0xFF
PortMask3=0xFF
PortMask4=0x0F

[ADCPins]
ADC0=2
ADC1=3
ADC2=4
ADC3=5
ADC4=6
ADC5=7
ADC6=8
ADC7=9
ADC8=10

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#include <system.h>\n#pragma CLOCK_FREQ %c\n"
MainStart="void main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n}\n\n"
IntStart="void interrupt(void)\n{\n"
IntEnd="}\n\n"
Initialise="ansel0 = 0x00;\nansel1 = 0x00;\n"
IntInit="\n\n"
InputCmdFull="tris%p = tris%p | %m;\n%o = port%p;\n"
InputCmdOneBit="tris%p = tris%p | %m;\n%o = ((port%p & %m) == %m);\n"
InputCmdMask="tris%p = tris%p | %m;\n%o = port%p & %m;\n"
OutputCmdFull="tris%p = 0x00;\nport%p = %o;\n"
OutputCmdOneBit="tris%p = tris%p & %i;\nif (%o)\n\tport%p = (port%p & %i) | %m;\nelse\n\tport%p = port%p & %i;\n"
OutputCmdMask="tris%p = tris%p & %i;\nport%p = (port%p & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
ADCCapture="//set up ADC conversion\nchar old_tris, cnt;\n#define MX_ADC_SAMP_TIME 40\nadcon2 = 0x07;\nadchs = 0x00;\n\n//find appropriate bit\n#if (%a == 0)\n  #define MX_ADC_TRIS_REG  trisa\n  #define MX_ADC_TRIS_MSK  0x01\n  adcon0 = 0x00;\n  ansel0 = 0x01;\n#endif\n#if (%a == 1)\n  #define MX_ADC_TRIS_REG  trisa\n  #define MX_ADC_TRIS_MSK  0x02\n  adcon0 = 0x04;\n  ansel0 = 0x02;\n#endif\n#if (%a == 2)\n  #define MX_ADC_TRIS_REG  trisa\n  #define MX_ADC_TRIS_MSK  0x04\n  adcon0 = 0x08;\n  ansel0 = 0x04;\n#endif\n#if (%a == 3)\n  #define MX_ADC_TRIS_REG  trisa\n  #define MX_ADC_TRIS_MSK  0x08\n  adcon0 = 0x0C;\n  ansel0 = 0x08;\n#endif\n#if (%a == 4)\n  #define MX_ADC_TRIS_REG  trisa\n  #define MX_ADC_TRIS_MSK  0x10\n  adcon0 = 0x00;\n  adchs = 0x01;\n  ansel0 = 0x10;\n#endif\n#if (%a == 5)\n  #define MX_ADC_TRIS_REG  trisa\n  #define MX_ADC_TRIS_MSK  0x20\n  adcon0 = 0x04;\n  adchs = 0x10;\n  ansel0 = 0x20;\n#endif\n#if (%a == 6)\n  #define MX_ADC_TRIS_REG  trise\n  #define MX_ADC_TRIS_MSK  0x01\n  adcon0 = 0x08;\n  adchs = 0x04;\n  ansel0 = 0x40;\n#endif\n#if (%a == 7)\n  #define MX_ADC_TRIS_REG  trise\n  #define MX_ADC_TRIS_MSK  0x02\n  adcon0 = 0x0C;\n  adchs = 0x40;\n  ansel0 = 0x80;\n#endif\n#if (%a == 8)\n  #define MX_ADC_TRIS_REG  trisb\n  #define MX_ADC_TRIS_MSK  0x04\n  adcon0 = 0x00;\n  adchs = 0x02;\n  ansel1 = 0x01;\n#endif\n\n//sanity check\n#ifndef MX_ADC_TRIS_REG\n  #pragma error ADC conversion code error - please contact technical support\n#endif\n \n//store old tris value, and set the i/o pin as an input\nold_tris = MX_ADC_TRIS_REG;\nMX_ADC_TRIS_REG = MX_ADC_TRIS_REG | MX_ADC_TRIS_MSK;\n \n//turn ADC on\nadcon0 = adcon0 | 0x01;\n \n//wait the acquisition time\ncnt = 0;\nwhile (cnt < MX_ADC_SAMP_TIME) cnt++;\n \n//begin conversion and wait until it has finished\nadcon0 = adcon0 | 0x02;\nwhile (adcon0 & 0x02);\n \n//restore old tris value, and reset adc registers\nMX_ADC_TRIS_REG = old_tris;\nadcon0 = 0x00;\nansel0 = 0x00;\nansel1 = 0x00;\n \n#undef MX_ADC_TRIS_REG\n#undef MX_ADC_TRIS_MSK\n#undef MX_ADC_SAMP_TIME\n"
ADCHigh="return adresh;\n"
ADCLow="char adclow;\nadclow = adresl;\nreturn adclow;\n"
ADCFull="short iRetVal;\niRetVal = (adresh << 2);\niRetVal += (adresl >> 6);\nreturn (iRetVal);\n"

InitialPortLetter="a"
ConfigData="#pragma DATA %a, %v\n"
IntHandler="if (%r & (1 << %b))\n{\n\tFCM_%n();\n\tclear_bit(%r, %b);\n}\n"

[Defines]
Define1=#define P18F4331
Define2=#define MX_EE
Define3=#define MX_EE_TYPE3
Define4=#define MX_EE_SIZE 256
Define5=#define MX_SPI
Define6=#define MX_SPI_D
Define7=#define MX_SPI_SDI 2
Define8=#define MX_SPI_SDO 1
Define9=#define MX_SPI_SCK 3
Define10=#define MX_UART
Define11=#define MX_UART_C
Define12=#define MX_UART_TX 6
Define13=#define MX_UART_RX 7
Define14=#define MX_I2C
Define15=#define MX_I2C_D
Define16=#define MX_I2C_SDA 2
Define17=#define MX_I2C_SCL 3
Define18=#define MX_PWM
Define19=#define MX_PWM_CNT 2
Define20=#define MX_PWM_TRIS1 trisc
Define21=#define MX_PWM_1 2
Define22=#define MX_PWM_TRIS2 trisc
Define23=#define MX_PWM_2 1

[Interrupts]
;first 3 should always be 1=TMR0, 2=RB0INT, 3=PORTB
;any other interrupts need to also have this set: "intcon.PEIE=1;\n"5
GeneralInit="intcon.GIE=1;\n"
Count=6
1=TMR0
2=RB0INT
3=PORTB
4=RB1INT
5=RB2INT
6=USART_RX

[TMR0]
;it is vital that this section remains exactly as-is (for all chips?)
Name=(this is retrieved from the resource file)
FlagReg=intcon
FlagBit=TMR0IF
EnReg=intcon
EnBit=TMR0IE
OptCnt=3
TmrOpt=3
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T0CKI pin"
Opt1_1Val="t0con.T0CS=1;\n"
Opt1_2="Internal clock (CLKO)"
Opt1_2Val="t0con.T0CS=0;\n"
Opt2="Source Edge Select"
Opt2Cnt=2
Opt2_1="high-to-low transition on T0CKI"
Opt2_1Val="t0con.T0SE=1;\n"
Opt2_2="low-to-high transition on T0CKI"
Opt2_2Val="t0con.T0SE=0;\n"
Opt3="Prescaler Rate"
Opt3Cnt=9
Opt3_1="1:1"
Opt3_1Val="t0con = (t0con & 0xF0) | 0x08;\n"
Opt3_2="1:2"
Opt3_2Val="t0con = (t0con & 0xF0) | 0x00;\n"
Opt3_3="1:4"
Opt3_3Val="t0con = (t0con & 0xF0) | 0x01;\n"
Opt3_4="1:8"
Opt3_4Val="t0con = (t0con & 0xF0) | 0x02;\n"
Opt3_5="1:16"
Opt3_5Val="t0con = (t0con & 0xF0) | 0x03;\n"
Opt3_6="1:32"
Opt3_6Val="t0con = (t0con & 0xF0) | 0x04;\n"
Opt3_7="1:64"
Opt3_7Val="t0con = (t0con & 0xF0) | 0x05;\n"
Opt3_8="1:128"
Opt3_8Val="t0con = (t0con & 0xF0) | 0x06;\n"
Opt3_9="1:256"
Opt3_9Val="t0con = (t0con & 0xF0) | 0x07;\n"

[RB0INT]
Name=(this is retrieved from the resource file)
FlagReg=intcon
FlagBit=INT0IF
EnReg=intcon
EnBit=INT0IE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB0/INT0"
Opt1_1Val="intcon2.INTEDG0=1;\n"
Opt1_2="falling edge of RB0/INT0"
Opt1_2Val="intcon2.INTEDG0=0;\n"

[PORTB]
Name=(this is retrieved from the resource file)
FlagReg=intcon
FlagBit=RBIF
EnReg=intcon
EnBit=RBIE
OptCnt=0
TmrOpt=0

[RB1INT]
Name=RB1/INT1
FlagReg=intcon3
FlagBit=INT1IF
EnReg=intcon3
EnBit=INT1IE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB1/INT1"
Opt1_1Val="intcon2.INTEDG1=1;\n"
Opt1_2="falling edge of RB1/INT1"
Opt1_2Val="intcon2.INTEDG1=0;\n"

[RB2INT]
Name=RB2/INT2
FlagReg=intcon3
FlagBit=INT2IF
EnReg=intcon3
EnBit=INT2IE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB2/INT2"
Opt1_1Val="intcon2.INTEDG2=1;\n"
Opt1_2="falling edge of RB2/INT2"
Opt1_2Val="intcon2.INTEDG2=0;\n"

[USART_RX]
Name="Réception USART"
UseExplicitHandlerCode=1
FlagReg=
FlagBit=
HandlerCode="if (pir1 & (1 << RCIF))\n{\n  FCM_%n(); // call selected macro\n}\n"
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="intcon.PEIE = 1; // Enable peripheral interrupts\nintcon.GIE = 1;  // Enable global interrupts\npie1.RCIE = 1;   // Enable USART receive interrupts\nrcsta.CREN=1;    // Enable reception\n"
DisableCode="pie1.RCIE = 0; // Disable USART receive interrupts\n" 
OptCnt=0
TmrOpt=0