[Device]
Pins=18
Ports=2
ADCPins=0
ADCBits=0
MaxClock=20000000
PrescalerBits=3
ClockDivider=4
ConfigAddress=0x2007
ConfigCount=1
PortBits=8
PWMCount=1
UARTCount=1
SPICount=0
I2CCount=0
CANCount=0
ComparatorCount=2
TimerCount8=2
TimerCount16=1
EepromSize=256
HasAltPWM=0
FlowcodeProduct=PIC
UsesGpio=0
DefaultPackageType=0
FlashSize=7168
RamSize=256

[ICD]
ClockPort=1
ClockPin=6
DataPort=1
DataPin=7


[Pins]
Pin1="RA2/AN2/Vref"
Pin2="RA3/AN3/CMP1"
Pin3="RA4/T0CKI/CMP2"
Pin4="RA5/MCLR/VPP"
Pin5="Vss"
Pin6="RB0/INT"
Pin7="RB1/RX/DT"
Pin8="RB2/TX/CK"
Pin9="RB3/CCP1"
Pin10="RB4/PGM"
Pin11="RB5"
Pin12="RB6/T1OSO/T1CKI"
Pin13="RB7/T1OSI"
Pin14="Vdd"
Pin15="RA6/OSC2/CLKOUT"
Pin16="RA7/OSC1/CLKIN"
Pin17="RA0/AN0"
Pin18="RA1/AN1"

[Ports]
PortPin1=0x0002
PortPin2=0x0003
PortPin3=0x0004
PortPin4=0x0005
PortPin6=0x0100
PortPin7=0x0101
PortPin8=0x0102
PortPin9=0x0103
PortPin10=0x0104
PortPin11=0x0105
PortPin12=0x0106
PortPin13=0x0107
PortPin15=0x0006
PortPin16=0x0007
PortPin17=0x0000
PortPin18=0x0001

[PortMasks]
;NOTE: RA5-7 are unusable on our dev. board
PortMask0=0xFF
PortMask1=0xFF

[ADCPins]

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#define MX_CLK_SPEED %c\n#ifdef _BOOSTC\n#include <system.h>\n#endif\n#ifdef HI_TECH_C\n#include <pic.h>\n#endif\n"
MainStart="\nvoid main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n}\n\n"
IntStart="void MX_INTERRUPT_MACRO(void)\n{\n"
IntEnd="}\n\n"
Initialise="cmcon = 0x07;\n"
IntInit="option_reg = 0xC0;\n\n"
InputCmdFull="tris%p = tris%p | %m;\n%o = port%p;\n"
InputCmdOneBit="tris%p = tris%p | %m;\n%o = ((port%p & %m) == %m);\n"
InputCmdMask="tris%p = tris%p | %m;\n%o = port%p & %m;\n"
OutputCmdFull="tris%p = 0x00;\nport%p = %o;\n"
OutputCmdOneBit="tris%p = tris%p & %i;\nif (%o)\n\tport%p = (port%p & %i) | %m;\nelse\n\tport%p = port%p & %i;\n"
OutputCmdMask="tris%p = tris%p & %i;\nport%p = (port%p & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
DelayCmdUs="delay_us(%o);\n"
WdtDelayCmdS="Wdt_Delay_S(%o);\n"
WdtDelayCmdMs="Wdt_Delay_Ms(%o);\n"
InitialPortLetter="a"
ConfigData="#ifdef _BOOSTC\n#pragma DATA %a, %v\n#endif\n#ifdef HI_TECH_C\n__CONFIG(%v);\n#endif\n"
IntHandler="#ifndef MX_INTHANDLER_%r_%b\n#define MX_INTHANDLER_%r_%b\nif (ts_bit(%r, %b))\n{\n\tFCM_%n();\n\tcr_bit(%r, %b);\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif"

[Defines]
Define1=#define P16F648A
Define2=#define FC_CAL_PIC
Define3=#define MX_EE
Define4=#define MX_EE_TYPE1
Define5=#define MX_EE_SIZE 256
Define6=#define MX_UART_1
Define7=#define MX_UART_1_TX_PORT portb
Define8=#define MX_UART_1_TX_TRIS trisb
Define9=#define MX_UART_1_TX_PIN 2
Define10=#define MX_UART_1_RX_PORT portb
Define11=#define MX_UART_1_RX_TRIS trisb
Define12=#define MX_UART_1_RX_PIN 1
Define13=#define MX_PWM
Define14=#define MX_PWM_CNT 1
Define15=#define MX_PWM_PSCA1
Define16=#define MX_PWM_PSCA4
Define17=#define MX_PWM_PSCA16
Define18=#define MX_PWM_1_PORT portb
Define19=#define MX_PWM_1_TRIS trisb
Define20=#define MX_PWM_1_PIN 3

[Interrupts]
;first 3 should always be 1=TMR0, 2=RB0INT, 3=PORTB
;any other interrupts need to also have this set: "st_bit(intcon,PEIE);\n"
GeneralInit="st_bit(intcon,GIE);\n"
Count=6
1=TMR0
2=RB0INT
3=PORTB
4=TMR1
5=RXINT
6=TMR2

[TMR0]
Name="TMR0"
HandlerCode="#ifndef MX_INTHANDLER_intcon_T0IF\n#define MX_INTHANDLER_intcon_T0IF\nif (ts_bit(intcon, T0IF) && ts_bit(intcon, T0IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(intcon, T0IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(intcon, T0IE);\n"
DisableCode="cr_bit(intcon, T0IE);\n"
OptCnt=3
PrescaleOpt=3
MaxTimerOverflow=256
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T0CKI pin"
Opt1_1Val="st_bit(option_reg,T0CS);\n"
Opt1_2="Internal clock (CLKO)"
Opt1_2Val="cr_bit(option_reg,T0CS);\n"
Opt2="Source Edge Select"
Opt2Cnt=2
Opt2_1="high-to-low transition on TMR0 Clock"
Opt2_1Val="st_bit(option_reg,T0SE);\n"
Opt2_2="low-to-high transition on TMR0 Clock"
Opt2_2Val="cr_bit(option_reg,T0SE);\n"
Opt3="Prescaler Rate"
Opt3Cnt=9
Opt3_1="1:1"
Opt3_1Val="option_reg = (option_reg & 0xF0) | 0x08;\n"
Opt3_2="1:2"
Opt3_2Val="option_reg = (option_reg & 0xF0) | 0x00;\n"
Opt3_3="1:4"
Opt3_3Val="option_reg = (option_reg & 0xF0) | 0x01;\n"
Opt3_4="1:8"
Opt3_4Val="option_reg = (option_reg & 0xF0) | 0x02;\n"
Opt3_5="1:16"
Opt3_5Val="option_reg = (option_reg & 0xF0) | 0x03;\n"
Opt3_6="1:32"
Opt3_6Val="option_reg = (option_reg & 0xF0) | 0x04;\n"
Opt3_7="1:64"
Opt3_7Val="option_reg = (option_reg & 0xF0) | 0x05;\n"
Opt3_8="1:128"
Opt3_8Val="option_reg = (option_reg & 0xF0) | 0x06;\n"
Opt3_9="1:256"
Opt3_9Val="option_reg = (option_reg & 0xF0) | 0x07;\n"

[RB0INT]
Name="INT"
REMask=0x00,0x01
FEMask=0x00,0x01
ConfOpt=0x03
EdgeOpt=0x01
HandlerCode="#ifndef MX_INTHANDLER_intcon_INTF\n#define MX_INTHANDLER_intcon_INTF\nif (ts_bit(intcon, INTF) && ts_bit(intcon, INTE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(intcon, INTF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(intcon, INTE);\n"
DisableCode="cr_bit(intcon, INTE);\n"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of INT"
Opt1_1Val="st_bit(option_reg,INTEDG);\n"
Opt1_2="falling edge of INT"
Opt1_2Val="cr_bit(option_reg,INTEDG);\n"

[PORTB]
Name="PORT"
REMask=0x00,0xF0
FEMask=0x00,0xF0
ConfOpt=0x04
HandlerCode="#ifndef MX_INTHANDLER_intcon_RBIF\n#define MX_INTHANDLER_intcon_RBIF\nchar mxtmp;\nif (ts_bit(intcon, RBIF) && ts_bit(intcon, RBIE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tmxtmp=portb;\n\tcr_bit(intcon, RBIF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(intcon, RBIE);\n"
DisableCode="cr_bit(intcon, RBIE);\n"
OptCnt=0

[TMR1]
;NOTE: this osc is enabled and turned on as part of the Opt1 code
Name="TMR1"
HandlerCode="#ifndef MX_INTHANDLER_pir1_TMR1IF\n#define MX_INTHANDLER_pir1_TMR1IF\nif (ts_bit(pir1, TMR1IF) && ts_bit(pie1, TMR1IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(pir1, TMR1IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(pie1, TMR1IE);\n"
DisableCode="cr_bit(pie1, TMR1IE);\n"
OptCnt=2
PrescaleOpt=2
MaxTimerOverflow=65536
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T1CKI pin"
Opt1_1Val="st_bit(intcon,PEIE);\nst_bit(t1con,T1OSCEN);\nst_bit(t1con,TMR1ON);\nst_bit(t1con,TMR1CS);\n"
Opt1_2="Internal clock (Fosc/4)"
Opt1_2Val="st_bit(intcon,PEIE);\nst_bit(t1con,T1OSCEN);\nst_bit(t1con,TMR1ON);\ncr_bit(t1con,TMR1CS);\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="t1con = t1con & 0x0F;\n"
Opt2_2="1:2"
Opt2_2Val="t1con = (t1con & 0x0F) | 0x10;\n"
Opt2_3="1:4"
Opt2_3Val="t1con = (t1con & 0x0F) | 0x20;\n"
Opt2_4="1:8"
Opt2_4Val="t1con = (t1con & 0x0F) | 0x30;\n"

[RXINT]
Name="RXINT"
HandlerCode="#ifndef MX_INTHANDLER_pir1_RCIF\n#define MX_INTHANDLER_pir1_RCIF\nif (ts_bit(pir1, RCIF) && ts_bit(pie1, RCIE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(pir1, RCIF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(pie1, RCIE);\nst_bit(intcon, PEIE);\n"
DisableCode="cr_bit(pie1, RCIE);\n"
OptCnt=0

[TMR2]
Name="TMR2"
HandlerCode="#ifndef MX_INTHANDLER_pir1_TMR2IF\n#define MX_INTHANDLER_pir1_TMR2IF\nif (ts_bit(pir1, TMR2IF) && ts_bit(pie1, TMR2IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(pir1, TMR2IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(pie1, TMR2IE);\n"
DisableCode="cr_bit(pie1, TMR2IE);\n"
OptCnt=3
PrescaleOpt=1
PostScaleOpt=2
RolloverOpt=3
MaxTimerOverflow=256
Opt1="Prescaler Rate"
Opt1Cnt=3
Opt1_1="1:1"
Opt1_1Val="st_bit(intcon,PEIE);\ncr_bit(t2con,T2CKPS0);\ncr_bit(t2con,T2CKPS1);\nst_bit(t2con,TMR2ON);\n"
Opt1_2="1:4"
Opt1_2Val="st_bit(intcon,PEIE);\nst_bit(t2con,T2CKPS0);\ncr_bit(t2con,T2CKPS1);\nst_bit(t2con,TMR2ON);\n"
Opt1_3="1:16"
Opt1_3Val="st_bit(intcon,PEIE);\ncr_bit(t2con,T2CKPS0);\nst_bit(t2con,T2CKPS1);\nst_bit(t2con,TMR2ON);\n"
Opt2="Postscaler Rate"
Opt2Cnt=16
Opt2_1="1:1"
Opt2_1Val="t2con = t2con & 0x07;\n"
Opt2_2="1:2"
Opt2_2Val="t2con = (t2con & 0x07) | 0x08;\n"
Opt2_3="1:3"
Opt2_3Val="t2con = (t2con & 0x07) | 0x10;\n"
Opt2_4="1:4"
Opt2_4Val="t2con = (t2con & 0x07) | 0x18;\n"
Opt2_5="1:5"
Opt2_5Val="t2con = (t2con & 0x07) | 0x20;\n"
Opt2_6="1:6"
Opt2_6Val="t2con = (t2con & 0x07) | 0x28;\n"
Opt2_7="1:7"
Opt2_7Val="t2con = (t2con & 0x07) | 0x30;\n"
Opt2_8="1:8"
Opt2_8Val="t2con = (t2con & 0x07) | 0x38;\n"
Opt2_9="1:9"
Opt2_9Val="t2con = (t2con & 0x07) | 0x40;\n"
Opt2_10="1:10"
Opt2_10Val="t2con = (t2con & 0x07) | 0x48;\n"
Opt2_11="1:11"
Opt2_11Val="t2con = (t2con & 0x07) | 0x50;\n"
Opt2_12="1:12"
Opt2_12Val="t2con = (t2con & 0x07) | 0x58;\n"
Opt2_13="1:13"
Opt2_13Val="t2con = (t2con & 0x07) | 0x60;\n"
Opt2_14="1:14"
Opt2_14Val="t2con = (t2con & 0x07) | 0x68;\n"
Opt2_15="1:15"
Opt2_15Val="t2con = (t2con & 0x07) | 0x70;\n"
Opt2_16="1:16"
Opt2_16Val="t2con = (t2con & 0x07) | 0x78;\n"
Opt3="Rollover Value"
Opt3Cnt=5
Opt3_1="256"
Opt3_1Val="pr2=%d-1;\n"
Opt3_2="128"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="64"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="32"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="16"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"