[Device]
Pins=64
Ports=7
ADCPins=17
ADCBits=10
ADCType=23
MaxClock=32000000
PrescalerBits=3
ClockDivider=4
ConfigAddress=0x8007
ConfigCount=2
PWMCount=2
UARTCount=2
EepromSize=256
HasAltPWM=1
Pwm2IsD4=0
FlowcodeProduct=PIC
UsesGpio=0
DefaultPackageType=1
FlashSize=16384
RamSize=512

[ICD]
ClockPort=1
ClockPin=6
DataPort=1
DataPin=7

[Pins]
Pin1 = "RE1"
Pin2 = "RE0"
Pin3 = "RG0"
Pin4 = "RG1/AN15/TX2"
Pin5 = "RG2/AN14/RX2"
Pin6 = "RG3/AN13"
Pin7 = "RG5/MCLR"
Pin8 = "RG4/AN12"
Pin9 = "VSS"
Pin10 = "VDD"
Pin11 = "RF7/AN5"
Pin12 = "RF6/AN11"
Pin13 = "RF5/AN10"
Pin14 = "RF4/AN9"
Pin15 = "RF3/AN8"
Pin16 = "RF2/AN7"
Pin17 = "RF1/AN6"
Pin18 = "RF0/AN16"
Pin19 = "AVDD"
Pin20 = "AVSS"
Pin21 = "RA3/AN3"
Pin22 = "RA2/AN2"
Pin23 = "RA1/AN1"
Pin24 = "RA0/AN0"
Pin25 = "VSS"
Pin26 = "VDD"
Pin27 = "RA5/AN4"
Pin28 = "RA4/T0CKI"
Pin29 = "RC1/CCP2"
Pin30 = "RC0"
Pin31 = "RC6/TX1"
Pin32 = "RC7/RX1"
Pin33 = "RC2/CCP1"
Pin34 = "RC3/SCK1/SCL1"
Pin35 = "RC4/SDI1/SDA1"
Pin36 = "RC5/SDO1"
Pin37 = "RB7/PGD"
Pin38 = "VDD"
Pin39 = "RA7/OSC1"
Pin40 = "RA6/OSC2"
Pin41 = "VSS"
Pin42 = "RB6/PGC"
Pin43 = "RB5"
Pin44 = "RB4"
Pin45 = "RB3"
Pin46 = "RB2"
Pin47 = "RB1"
Pin48 = "RB0/INT"
Pin49 = "RD7"
Pin50 = "RD6/SCK2/SCL2"
Pin51 = "RD5/SDI2/SDA2"
Pin52 = "RD4/SDO2"
Pin53 = "RD3"
Pin54 = "RD2"
Pin55 = "RD1"
Pin56 = "VSS"
Pin57 = "VDD"
Pin58 = "RD0"
Pin59 = "RE7/CCP2"
Pin60 = "RE6"
Pin61 = "RE5"
Pin62 = "RE4"
Pin63 = "RE3"
Pin64 = "RE2"

[Ports]
PortPin1=0x0401
PortPin2=0x0400
PortPin3=0x0600
PortPin4=0x0601
PortPin5=0x0602
PortPin6=0x0603
PortPin7=0x0605
PortPin8=0x0604
PortPin11=0x0507
PortPin12=0x0506
PortPin13=0x0505
PortPin14=0x0504
PortPin15=0x0503
PortPin16=0x0502
PortPin17=0x0501
PortPin18=0x0500
PortPin21=0x0003
PortPin22=0x0002
PortPin23=0x0001
PortPin24=0x0000
PortPin27=0x0005
PortPin28=0x0004
PortPin29=0x0201
PortPin30=0x0200
PortPin31=0x0206
PortPin32=0x0207
PortPin33=0x0202
PortPin34=0x0203
PortPin35=0x0204
PortPin36=0x0205
PortPin37=0x0107
PortPin39=0x0007
PortPin40=0x0006
PortPin42=0x0106
PortPin43=0x0105
PortPin44=0x0104
PortPin45=0x0103
PortPin46=0x0102
PortPin47=0x0101
PortPin48=0x0100
PortPin49=0x0307
PortPin50=0x0306
PortPin51=0x0305
PortPin52=0x0304
PortPin53=0x0303
PortPin54=0x0302
PortPin55=0x0301
PortPin58=0x0300
PortPin59=0x0407
PortPin60=0x0406
PortPin61=0x0405
PortPin62=0x0404
PortPin63=0x0403
PortPin64=0x0402

[PortMasks]
PortMask0=0xFF
PortMask1=0xFF
PortMask2=0xFF
PortMask3=0xFF
PortMask4=0xFF
PortMask5=0xFF
PortMask6=0x3F

[ADCPins]
ADC0=24
ADC1=23
ADC2=22
ADC3=21
ADC4=27
ADC5=11
ADC6=17
ADC7=16
ADC8=15
ADC9=14
ADC10=13
ADC11=12
ADC12=8
ADC13=6
ADC14=5
ADC15=4
ADC16=18

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#define MX_CLK_SPEED %c\n#ifdef _BOOSTC\n#include <system.h>\n#endif\n#ifdef HI_TECH_C\n#include <pic.h>\n#endif\n"
MainStart="void main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n}\n\n"
IntStart="void MX_INTERRUPT_MACRO(void)\n{\n"
IntEnd="}\n\n"
Initialise="ansela = 0x00;\nanself = 0x00;\nanselg = 0x00;\n"
IntInit="option_reg = 0xC0;\n\n"
InputCmdFull="tris%p = tris%p | %m;\n%o = port%p;\n"
InputCmdOneBit="tris%p = tris%p | %m;\n%o = ((port%p & %m) == %m);\n"
InputCmdMask="tris%p = tris%p | %m;\n%o = port%p & %m;\n"
OutputCmdFull="tris%p = 0x00;\nport%p = %o;\n"
OutputCmdOneBit="tris%p = tris%p & %i;\nif (%o)\n\tport%p = (port%p & %i) | %m;\nelse\n\tport%p = port%p & %i;\n"
OutputCmdMask="tris%p = tris%p & %i;\nport%p = (port%p & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
DelayCmdUs="delay_us(%o);\n"
WdtDelayCmdS="Wdt_Delay_S(%o);\n"
WdtDelayCmdMs="Wdt_Delay_Ms(%o);\n"
InitialPortLetter="a"
ConfigData="#ifdef _BOOSTC\n#pragma DATA %a, %v\n#endif\n#ifdef HI_TECH_C\n__CONFIG(%v);\n#endif\n"
IntHandler="#ifndef MX_INTHANDLER_%r_%b\n#define MX_INTHANDLER_%r_%b\nif (ts_bit(%r, %b))\n{\n\tFCM_%n();\n\tcr_bit(%r, %b);\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif"

[Defines]
Define1=#define P16LF1946
Define2=#define MX_EE
Define3=#define MX_EE_TYPE1
Define4=#define MX_EE_SIZE 256
Define5=#define MX_SPI
Define6=#define MX_SPI_C
Define7=#define MX_SPI_SDI 4
Define8=#define MX_SPI_SDO 5
Define9=#define MX_SPI_SCK 3
Define10=#define MX_UART
Define11=#define MX_UART_C
Define12=#define MX_UART_TX 6
Define13=#define MX_UART_RX 7
Define14=#define MX_I2C
Define15=#define MX_MI2C
Define16=#define MX_I2C_C
Define17=#define MX_I2C_SDA 4
Define18=#define MX_I2C_SCL 3
Define19=#define MX_PWM
Define20=#define MX_PWM_CNT 2
Define21=#define MX_PWM_TRIS1 trisc
Define22=#define MX_PWM_1 2
Define23=#define MX_PWM_TRIS2 trisc
Define24=#define MX_PWM_2 1
Define25=#define MX_PWM_TRIS2a trise
Define26=#define MX_PWM_2a 7

[Interrupts]
;first 3 should always be 1=TMR0, 2=RB0INT, 3=PORTB
;any other interrupts need to also have this set: "st_bit(intcon,PEIE);\n"
GeneralInit="st_bit(intcon,GIE);\n"
Count=5
1=TMR0
2=RB0INT
3=TMR1
4=RXINT
5=TMR2

[TMR0]
Name="TMR0"
FlagReg=
FlagBit=
HandlerCode="#ifndef MX_INTHANDLER_intcon_TMR0IF\n#define MX_INTHANDLER_intcon_TMR0IF\nif (ts_bit(intcon, TMR0IF) && ts_bit(intcon, TMR0IE))\n{\n\tFCM_%n();\n\tcr_bit(intcon, TMR0IF);\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
UseExplicitHandlerCode=1
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="st_bit(intcon, TMR0IE);\n"
DisableCode="cr_bit(intcon, TMR0IE);\n"
OptCnt=3
PrescaleOpt=3
MaxTimerOverflow=256
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T0CKI pin"
Opt1_1Val="st_bit(option_reg,T0CS);\n"
Opt1_2="Internal clock (CLKO)"
Opt1_2Val="cr_bit(option_reg,T0CS);\n"
Opt2="Source Edge Select"
Opt2Cnt=2
Opt2_1="high-to-low transition on TMR0 Clock"
Opt2_1Val="st_bit(option_reg,T0SE);\n"
Opt2_2="low-to-high transition on TMR0 Clock"
Opt2_2Val="cr_bit(option_reg,T0SE);\n"
Opt3="Prescaler Rate"
Opt3Cnt=9
Opt3_1="1:1"
Opt3_1Val="option_reg = (option_reg & 0xF0) | 0x08;\n"
Opt3_2="1:2"
Opt3_2Val="option_reg = (option_reg & 0xF0) | 0x00;\n"
Opt3_3="1:4"
Opt3_3Val="option_reg = (option_reg & 0xF0) | 0x01;\n"
Opt3_4="1:8"
Opt3_4Val="option_reg = (option_reg & 0xF0) | 0x02;\n"
Opt3_5="1:16"
Opt3_5Val="option_reg = (option_reg & 0xF0) | 0x03;\n"
Opt3_6="1:32"
Opt3_6Val="option_reg = (option_reg & 0xF0) | 0x04;\n"
Opt3_7="1:64"
Opt3_7Val="option_reg = (option_reg & 0xF0) | 0x05;\n"
Opt3_8="1:128"
Opt3_8Val="option_reg = (option_reg & 0xF0) | 0x06;\n"
Opt3_9="1:256"
Opt3_9Val="option_reg = (option_reg & 0xF0) | 0x07;\n"

[RB0INT]
Name="INT"
FlagReg=
FlagBit=
HandlerCode="#ifndef MX_INTHANDLER_intcon_INTF\n#define MX_INTHANDLER_intcon_INTF\nif (ts_bit(intcon, INTF) && ts_bit(intcon, INTE))\n{\n\tFCM_%n();\n\tcr_bit(intcon, INTF);\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
UseExplicitHandlerCode=1
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="st_bit(intcon, INTE);\n"
DisableCode="cr_bit(intcon, INTE);\n"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of INT"
Opt1_1Val="st_bit(option_reg,INTEDG);\n"
Opt1_2="falling edge of INT"
Opt1_2Val="cr_bit(option_reg,INTEDG);\n"

[TMR1]
;NOTE: this osc is enabled and turned on as part of the Opt1 code
Name="TMR1"
FlagReg=
FlagBit=
HandlerCode="#ifndef MX_INTHANDLER_pir1_TMR1IF\n#define MX_INTHANDLER_pir1_TMR1IF\nif (ts_bit(pir1, TMR1IF) && ts_bit(pie1, TMR1IE))\n{\n\tFCM_%n();\n\tcr_bit(pir1, TMR1IF);\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif"
UseExplicitHandlerCode=1
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="st_bit(pie1, TMR1IE);\n"
DisableCode="cr_bit(pie1, TMR1IE);\n"
OptCnt=2
PrescaleOpt=2
MaxTimerOverflow=65536
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T1CKI pin"
Opt1_1Val="st_bit(intcon,PEIE);\nst_bit(t1con,T1OSCEN);\nst_bit(t1con,TMR1ON);\nst_bit(t1con,TMR1CS);\n"
Opt1_2="Internal clock (Fosc/4)"
Opt1_2Val="st_bit(intcon,PEIE);\nst_bit(t1con,T1OSCEN);\nst_bit(t1con,TMR1ON);\ncr_bit(t1con,TMR1CS);\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="t1con = t1con & 0x0F;\n"
Opt2_2="1:2"
Opt2_2Val="t1con = (t1con & 0x0F) | 0x10;\n"
Opt2_3="1:4"
Opt2_3Val="t1con = (t1con & 0x0F) | 0x20;\n"
Opt2_4="1:8"
Opt2_4Val="t1con = (t1con & 0x0F) | 0x30;\n"

[RXINT]
Name="RXINT"
FlagReg=
FlagBit=
HandlerCode="#ifndef MX_INTHANDLER_pir1_RCIF\n#define MX_INTHANDLER_pir1_RCIF\nif (ts_bit(pir1, RCIF) && ts_bit(pie1, RCIE))\n{\n\tFCM_%n();\n\tcr_bit(pir1, RCIF);\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif"
UseExplicitHandlerCode=1
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="st_bit(pie1, RCIE);\nst_bit(intcon, PEIE);\n"
DisableCode="cr_bit(pie1, RCIE);\n"
OptCnt=0

[TMR2]
Name="TMR2"
FlagReg=
FlagBit=
HandlerCode="#ifndef MX_INTHANDLER_pir1_TMR2IF\n#define MX_INTHANDLER_pir1_TMR2IF\nif (ts_bit(pir1, TMR2IF) && ts_bit(pie1, TMR2IE))\n{\n\tFCM_%n();\n\tcr_bit(pir1, TMR2IF);\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif"
UseExplicitHandlerCode=1
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="st_bit(pie1, TMR2IE);\n"
DisableCode="cr_bit(pie1, TMR2IE);\n"
OptCnt=3
PrescaleOpt=1
PostScaleOpt=2
RolloverOpt=3
MaxTimerOverflow=256
Opt1="Prescaler Rate"
Opt1Cnt=3
Opt1_1="1:1"
Opt1_1Val="st_bit(intcon,PEIE);\ncr_bit(t2con,T2CKPS0);\ncr_bit(t2con,T2CKPS1);\nst_bit(t2con,TMR2ON);\n"
Opt1_2="1:4"
Opt1_2Val="st_bit(intcon,PEIE);\nst_bit(t2con,T2CKPS0);\ncr_bit(t2con,T2CKPS1);\nst_bit(t2con,TMR2ON);\n"
Opt1_3="1:16"
Opt1_3Val="st_bit(intcon,PEIE);\ncr_bit(t2con,T2CKPS0);\nst_bit(t2con,T2CKPS1);\nst_bit(t2con,TMR2ON);\n"
Opt2="Postscaler Rate"
Opt2Cnt=16
Opt2_1="1:1"
Opt2_1Val="t2con = t2con & 0x07;\n"
Opt2_2="1:2"
Opt2_2Val="t2con = (t2con & 0x07) | 0x08;\n"
Opt2_3="1:3"
Opt2_3Val="t2con = (t2con & 0x07) | 0x10;\n"
Opt2_4="1:4"
Opt2_4Val="t2con = (t2con & 0x07) | 0x18;\n"
Opt2_5="1:5"
Opt2_5Val="t2con = (t2con & 0x07) | 0x20;\n"
Opt2_6="1:6"
Opt2_6Val="t2con = (t2con & 0x07) | 0x28;\n"
Opt2_7="1:7"
Opt2_7Val="t2con = (t2con & 0x07) | 0x30;\n"
Opt2_8="1:8"
Opt2_8Val="t2con = (t2con & 0x07) | 0x38;\n"
Opt2_9="1:9"
Opt2_9Val="t2con = (t2con & 0x07) | 0x40;\n"
Opt2_10="1:10"
Opt2_10Val="t2con = (t2con & 0x07) | 0x48;\n"
Opt2_11="1:11"
Opt2_11Val="t2con = (t2con & 0x07) | 0x50;\n"
Opt2_12="1:12"
Opt2_12Val="t2con = (t2con & 0x07) | 0x58;\n"
Opt2_13="1:13"
Opt2_13Val="t2con = (t2con & 0x07) | 0x60;\n"
Opt2_14="1:14"
Opt2_14Val="t2con = (t2con & 0x07) | 0x68;\n"
Opt2_15="1:15"
Opt2_15Val="t2con = (t2con & 0x07) | 0x70;\n"
Opt2_16="1:16"
Opt2_16Val="t2con = (t2con & 0x07) | 0x78;\n"
Opt3="Rollover Value"
Opt3Cnt=5
Opt3_1="256"
Opt3_1Val="pr2=%d-1;\n"
Opt3_2="128"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="64"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="32"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="16"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"