[Device]
Pins=20
Ports=3
ADCPins=12
ADCBits=10
ADCType=3
MaxClock=20000000
PrescalerBits=3
ClockDivider=4
ConfigAddress=0x2007
ConfigCount=1
PWMCount=1
UARTCount=1
EepromSize=256
HasAltPWM=0
Pwm2IsD4=0
FlowcodeProduct=PIC
UsesGpio=0
DefaultPackageType=0
FlashSize=7168
RamSize=256

[ICD]
ClockPort=0
ClockPin=1
DataPort=0
DataPin=0

[Pins]
Pin1="VDD"
Pin2="RA5/T1CKI/OSC1/CLKIN"
Pin3="RA4/AN3/T1G/OSC2/CLKOUT"
Pin4="RA3/MCLR/VPP"
Pin5="RC5/CCP1/P1A"
Pin6="RC4/C2OUT/P1B"
Pin7="RC3/AN7/C12IN3-"
Pin8="RC6/AN8/SS"
Pin9="RC7/AN9/SDO"
Pin10="RB7/TX/CK"
Pin11="RB6/SCK/SCL"
Pin12="RB5/AN11/RX/DT"
Pin13="RB4/AN10/SDI/SDA"
Pin14="RC2/AN6/C12IN2-/P1D"
Pin15="RC1/AN5/C12IN1-"
Pin16="RC0/AN4/C2IN+"
Pin17="RA2/AN2/T0CKI/INT/C1OUT"
Pin18="RA1/AN1/C12IN0-/VREF/ICSPCLK"
Pin19="RA0/AN0/C1IN+/ICSPDAT/ULPWU"
Pin20="VSS"

[Ports]
PortPin2=0x0005
PortPin3=0x0004
PortPin4=0x0003
PortPin5=0x0205
PortPin6=0x0204
PortPin7=0x0203
PortPin8=0x0206
PortPin9=0x0207
PortPin10=0x0107
PortPin11=0x0106
PortPin12=0x0105
PortPin13=0x0104
PortPin14=0x0202
PortPin15=0x0201
PortPin16=0x0200
PortPin17=0x0002
PortPin18=0x0001
PortPin19=0x0000

[PortMasks]
PortMask0=0x3F
PortMask1=0xF0
PortMask2=0xFF

[ADCPins]
ADC0=19
ADC1=18
ADC2=17
ADC3=3
ADC4=16
ADC5=15
ADC6=14
ADC7=7
ADC8=8
ADC9=9
ADC10=13
ADC11=12

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#define MX_CLK_SPEED %c\n#ifdef _BOOSTC\n#include <system.h>\n#endif\n#ifdef HI_TECH_C\n#include <pic.h>\n#endif\n"
MainStart="void main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n}\n\n"
IntStart="void MX_INTERRUPT_MACRO(void)\n{\n"
IntEnd="}\n\n"
Initialise="ansel = 0;\nanselh = 0;\n"
IntInit="option_reg = 0xC0;\n\n"
InputCmdFull="tris%p = tris%p | %m;\n%o = port%p;\n"
InputCmdOneBit="tris%p = tris%p | %m;\n%o = ((port%p & %m) == %m);\n"
InputCmdMask="tris%p = tris%p | %m;\n%o = port%p & %m;\n"
OutputCmdFull="tris%p = 0x00;\nport%p = %o;\n"
OutputCmdOneBit="tris%p = tris%p & %i;\nif (%o)\n\tport%p = (port%p & %i) | %m;\nelse\n\tport%p = port%p & %i;\n"
OutputCmdMask="tris%p = tris%p & %i;\nport%p = (port%p & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
DelayCmdUs="delay_us(%o);\n"
WdtDelayCmdS="Wdt_Delay_S(%o);\n"
WdtDelayCmdMs="Wdt_Delay_Ms(%o);\n"
InitialPortLetter="a"
ConfigData="#ifdef _BOOSTC\n#pragma DATA %a, %v\n#endif\n#ifdef HI_TECH_C\n__CONFIG(%v);\n#endif\n"
IntHandler="#ifndef MX_INTHANDLER_%r_%b\n#define MX_INTHANDLER_%r_%b\nif (ts_bit(%r, %b))\n{\n\tFCM_%n();\n\tcr_bit(%r, %b);\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif"

[Defines]
Define1=#define P16F690
Define2=#define MX_EE
Define3=#define MX_EE_TYPE2
Define4=#define MX_EE_SIZE 256
Define5=#define MX_SPI
Define6=#define MX_SPI_BCB
Define7=#define MX_SPI_SDI 4
Define8=#define MX_SPI_SDO 7
Define9=#define MX_SPI_SCK 6
Define10=#define MX_UART
Define11=#define MX_UART_B
Define12=#define MX_UART_TX 7
Define13=#define MX_UART_RX 5
Define14=#define MX_I2C
Define15=#define MX_MI2C
Define16=#define MX_I2C_B
Define17=#define MX_I2C_SDA 4
Define18=#define MX_I2C_SCL 6
Define19=#define MX_PWM
Define20=#define MX_PWM_CNT 1
Define21=#define MX_PWM_TRIS1 trisc
Define22=#define MX_PWM_1 5

[Interrupts]
;first 3 should always be 1=TMR0, 2=RB0INT, 3=PORTB
;any other interrupts need to also have this set: "st_bit(intcon,PEIE);\n"
GeneralInit="st_bit(intcon,GIE);\n"
Count=6
1=TMR0
2=RB0INT
3=TMR1
4=PORTB
5=RXINT
6=TMR2

[TMR0]
Name="TMR0"
FlagReg=
FlagBit=
HandlerCode="#ifndef MX_INTHANDLER_intcon_T0IF\n#define MX_INTHANDLER_intcon_T0IF\nif (ts_bit(intcon, T0IF) && ts_bit(intcon, T0IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(intcon, T0IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
UseExplicitHandlerCode=1
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="st_bit(intcon, T0IE);\n"
DisableCode="cr_bit(intcon, T0IE);\n"
OptCnt=3
PrescaleOpt=3
MaxTimerOverflow=256
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T0CKI pin"
Opt1_1Val="st_bit(option_reg,T0CS);\n"
Opt1_2="Internal clock (CLKO)"
Opt1_2Val="cr_bit(option_reg,T0CS);\n"
Opt2="Source Edge Select"
Opt2Cnt=2
Opt2_1="high-to-low transition on TMR0 Clock"
Opt2_1Val="st_bit(option_reg,T0SE);\n"
Opt2_2="low-to-high transition on TMR0 Clock"
Opt2_2Val="cr_bit(option_reg,T0SE);\n"
Opt3="Prescaler Rate"
Opt3Cnt=9
Opt3_1="1:1"
Opt3_1Val="option_reg = (option_reg & 0xF0) | 0x08;\n"
Opt3_2="1:2"
Opt3_2Val="option_reg = (option_reg & 0xF0) | 0x00;\n"
Opt3_3="1:4"
Opt3_3Val="option_reg = (option_reg & 0xF0) | 0x01;\n"
Opt3_4="1:8"
Opt3_4Val="option_reg = (option_reg & 0xF0) | 0x02;\n"
Opt3_5="1:16"
Opt3_5Val="option_reg = (option_reg & 0xF0) | 0x03;\n"
Opt3_6="1:32"
Opt3_6Val="option_reg = (option_reg & 0xF0) | 0x04;\n"
Opt3_7="1:64"
Opt3_7Val="option_reg = (option_reg & 0xF0) | 0x05;\n"
Opt3_8="1:128"
Opt3_8Val="option_reg = (option_reg & 0xF0) | 0x06;\n"
Opt3_9="1:256"
Opt3_9Val="option_reg = (option_reg & 0xF0) | 0x07;\n"

[RB0INT]
Name="INT"
FlagReg=
FlagBit=
HandlerCode="#ifndef MX_INTHANDLER_intcon_INTF\n#define MX_INTHANDLER_intcon_INTF\nif (ts_bit(intcon, INTF) && ts_bit(intcon, INTE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(intcon, INTF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
UseExplicitHandlerCode=1
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="st_bit(intcon, INTE);\n"
DisableCode="cr_bit(intcon, INTE);\n"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of INT"
Opt1_1Val="st_bit(option_reg,INTEDG);\n"
Opt1_2="falling edge of INT"
Opt1_2Val="cr_bit(option_reg,INTEDG);\n"

[TMR1]
;NOTE: this osc is enabled and turned on as part of the Opt1 code
Name="TMR1"
FlagReg=
FlagBit=
HandlerCode="#ifndef MX_INTHANDLER_pir1_TMR1IF\n#define MX_INTHANDLER_pir1_TMR1IF\nif (ts_bit(pir1, TMR1IF) && ts_bit(pie1, TMR1IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(pir1, TMR1IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
UseExplicitHandlerCode=1
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="st_bit(pie1, TMR1IE);\n"
DisableCode="cr_bit(pie1, TMR1IE);\n"
OptCnt=2
PrescaleOpt=2
MaxTimerOverflow=65536
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T1CKI pin"
Opt1_1Val="st_bit(intcon,PEIE);\nst_bit(t1con,T1OSCEN);\nst_bit(t1con,TMR1ON);\nst_bit(t1con,TMR1CS);\n"
Opt1_2="Internal clock (Fosc/4)"
Opt1_2Val="st_bit(intcon,PEIE);\nst_bit(t1con,T1OSCEN);\nst_bit(t1con,TMR1ON);\ncr_bit(t1con,TMR1CS);\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="t1con = t1con & 0x0F;\n"
Opt2_2="1:2"
Opt2_2Val="t1con = (t1con & 0x0F) | 0x10;\n"
Opt2_3="1:4"
Opt2_3Val="t1con = (t1con & 0x0F) | 0x20;\n"
Opt2_4="1:8"
Opt2_4Val="t1con = (t1con & 0x0F) | 0x30;\n"

[PORTB]
Name="PORT"
FlagReg=
FlagBit=
HandlerCode="#ifndef MX_INTHANDLER_intcon_RABIF\n#define MX_INTHANDLER_intcon_RABIF\nchar mxtmp;\nif (ts_bit(intcon, RABIF) && ts_bit(intcon, RABIE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tmxtmp=porta;\n\tmxtmp=portb;\n\tcr_bit(intcon, RABIF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
UseExplicitHandlerCode=1
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="st_bit(intcon, RABIE);\n"
DisableCode="cr_bit(intcon, RABIE);\n"
OptCnt=4
Opt1="Interrupt Change On RA0,RA1,RA2"
Opt1Cnt=8
Opt1_1="RA0 On / RA1 On / RA2 On"
Opt1_1Val="ioca = ioca | 0x07;\n"
Opt1_2="RA0 Off / RA1 On / RA2 On"
Opt1_2Val="ioca = (ioca | 0x06) & 0xFE;\n"
Opt1_3="RA0 On / RA1 Off / RA2 On"
Opt1_3Val="ioca = (ioca | 0x05) & 0xFD;\n"
Opt1_4="RA0 Off / RA1 Off / RA2 On"
Opt1_4Val="ioca = (ioca | 0x04) & 0xFC;\n"
Opt1_5="RA0 On / RA1 On / RA2 Off"
Opt1_5Val="ioca = (ioca | 0x03) & 0xFB;\n"
Opt1_6="RA0 Off / RA1 On / RA2 Off"
Opt1_6Val="ioca = (ioca | 0x02) & 0xFA;\n"
Opt1_7="RA0 On / RA1 Off / RA2 Off"
Opt1_7Val="ioca = (ioca | 0x01) & 0xF9;\n"
Opt1_8="RA0 Off / RA1 Off / RA2 Off"
Opt1_8Val="ioca = ioca & 0xF8;\n"
Opt2="Interrupt Change On RA3,RA4,RA5"
Opt2Cnt=8
Opt2_1="RA3 On / RA4 On / RA5 On"
Opt2_1Val="ioca = ioca | 0x38;\n"
Opt2_2="RA3 Off / RA4 On / RA5 On"
Opt2_2Val="ioca = (ioca | 0x30) & 0xF7;\n"
Opt2_3="RA3 On / RA4 Off / RA5 On"
Opt2_3Val="ioca = (ioca | 0x28) & 0xEF;\n"
Opt2_4="RA3 Off / RA4 Off / RA5 On"
Opt2_4Val="ioca = (ioca | 0x20) & 0xE7;\n"
Opt2_5="RA3 On / RA4 On / RA5 Off"
Opt2_5Val="ioca = (ioca | 0x18) & 0xDF;\n"
Opt2_6="RA3 Off / RA4 On / RA5 Off"
Opt2_6Val="ioca = (ioca | 0x10) & 0xD7;\n"
Opt2_7="RA3 On / RA4 Off / RA5 Off"
Opt2_7Val="ioca = (ioca | 0x08) & 0xCF;\n"
Opt2_8="RA3 Off / RA4 Off / RA5 Off"
Opt2_8Val="ioca = ioca & 0xC7;\n"
Opt3="Interrupt On Change Enable RB4 / RB5"
Opt3Cnt=4
Opt3_1="RB4 On / RB5 On"
Opt3_1Val="iocb = iocb | 0x30;\n"
Opt3_2="RB4 Off / RB5 On"
Opt3_2Val="iocb = (iocb | 0x20) & 0xE0;\n"
Opt3_3="RB4 On / RB5 Off"
Opt3_3Val="iocb = (iocb | 0x10) & 0xD0;\n"
Opt3_4="RB4 Off / RB5 Off"
Opt3_4Val="iocb = iocb & 0xC0;\n"
Opt4="Interrupt On Change Enable RB6 / RB7"
Opt4Cnt=4
Opt4_1="RB6 On / RB7 On"
Opt4_1Val="iocb = iocb | 0xC0;\n"
Opt4_2="RB6 Off / RB7 On"
Opt4_2Val="iocb = (iocb | 0x80) & 0xB0;\n"
Opt4_3="RB6 On / RB7 Off"
Opt4_3Val="iocb = (iocb | 0x40) & 0x70;\n"
Opt4_4="RB6 Off / RB7 Off"
Opt4_4Val="iocb = iocb & 0x30;\n"

[RXINT]
Name="RXINT"
FlagReg=
FlagBit=
HandlerCode="#ifndef MX_INTHANDLER_pir1_RCIF\n#define MX_INTHANDLER_pir1_RCIF\nif (ts_bit(pir1, RCIF) && ts_bit(pie1, RCIE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(pir1, RCIF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
UseExplicitHandlerCode=1
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="st_bit(pie1, RCIE);\nst_bit(intcon, PEIE);\n"
DisableCode="cr_bit(pie1, RCIE);\n"
OptCnt=0

[TMR2]
Name="TMR2"
FlagReg=
FlagBit=
HandlerCode="#ifndef MX_INTHANDLER_pir1_TMR2IF\n#define MX_INTHANDLER_pir1_TMR2IF\nif (ts_bit(pir1, TMR2IF) && ts_bit(pie1, TMR2IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(pir1, TMR2IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
UseExplicitHandlerCode=1
UseExplicitEnableCode=1
EnReg=
EnBit=
EnableCode="st_bit(pie1, TMR2IE);\n"
DisableCode="cr_bit(pie1, TMR2IE);\n"
OptCnt=3
PrescaleOpt=1
PostScaleOpt=2
RolloverOpt=3
MaxTimerOverflow=256
Opt1="Prescaler Rate"
Opt1Cnt=3
Opt1_1="1:1"
Opt1_1Val="st_bit(intcon,PEIE);\ncr_bit(t2con,T2CKPS0);\ncr_bit(t2con,T2CKPS1);\nst_bit(t2con,TMR2ON);\n"
Opt1_2="1:4"
Opt1_2Val="st_bit(intcon,PEIE);\nst_bit(t2con,T2CKPS0);\ncr_bit(t2con,T2CKPS1);\nst_bit(t2con,TMR2ON);\n"
Opt1_3="1:16"
Opt1_3Val="st_bit(intcon,PEIE);\ncr_bit(t2con,T2CKPS0);\nst_bit(t2con,T2CKPS1);\nst_bit(t2con,TMR2ON);\n"
Opt2="Postscaler Rate"
Opt2Cnt=16
Opt2_1="1:1"
Opt2_1Val="t2con = t2con & 0x07;\n"
Opt2_2="1:2"
Opt2_2Val="t2con = (t2con & 0x07) | 0x08;\n"
Opt2_3="1:3"
Opt2_3Val="t2con = (t2con & 0x07) | 0x10;\n"
Opt2_4="1:4"
Opt2_4Val="t2con = (t2con & 0x07) | 0x18;\n"
Opt2_5="1:5"
Opt2_5Val="t2con = (t2con & 0x07) | 0x20;\n"
Opt2_6="1:6"
Opt2_6Val="t2con = (t2con & 0x07) | 0x28;\n"
Opt2_7="1:7"
Opt2_7Val="t2con = (t2con & 0x07) | 0x30;\n"
Opt2_8="1:8"
Opt2_8Val="t2con = (t2con & 0x07) | 0x38;\n"
Opt2_9="1:9"
Opt2_9Val="t2con = (t2con & 0x07) | 0x40;\n"
Opt2_10="1:10"
Opt2_10Val="t2con = (t2con & 0x07) | 0x48;\n"
Opt2_11="1:11"
Opt2_11Val="t2con = (t2con & 0x07) | 0x50;\n"
Opt2_12="1:12"
Opt2_12Val="t2con = (t2con & 0x07) | 0x58;\n"
Opt2_13="1:13"
Opt2_13Val="t2con = (t2con & 0x07) | 0x60;\n"
Opt2_14="1:14"
Opt2_14Val="t2con = (t2con & 0x07) | 0x68;\n"
Opt2_15="1:15"
Opt2_15Val="t2con = (t2con & 0x07) | 0x70;\n"
Opt2_16="1:16"
Opt2_16Val="t2con = (t2con & 0x07) | 0x78;\n"
Opt3="Rollover Value"
Opt3Cnt=5
Opt3_1="256"
Opt3_1Val="pr2=%d-1;\n"
Opt3_2="128"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="64"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="32"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="16"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"