[Device]
Pins=8
Ports=1
ADCPins=4
ADCBits=10
MaxClock=20000000
PrescalerBits=3
ClockDivider=4
ConfigAddress=0x2007
ConfigCount=1
PortBits=8
PWMCount=1
UARTCount=0
SPICount=0
I2CCount=0
CANCount=0
ComparatorCount=1
TimerCount8=2
TimerCount16=1
EepromSize=256
HasAltPWM=0
FlowcodeProduct=PIC
UsesGpio=1
DefaultPackageType=0
FlashSize=3584
RamSize=128

[ICD]
ClockPort=0
ClockPin=1
DataPort=0
DataPin=0


[Pins]
Pin1 = "VDD"
Pin2 = "GP5/OSC1"
Pin3 = "GP4/OSC2/AN3"
Pin4 = "GP3/MCLR/VPP"
Pin5 = "GP2/AN2"
Pin6 = "GP1/AN1"
Pin7 = "GP0/AN0"
Pin8 = "VSS"

[Ports]
PortPin7=0x0000
PortPin6=0x0001
PortPin5=0x0002
PortPin4=0x0003
PortPin3=0x0004
PortPin2=0x0005

[PortMasks]
;Only bits 0-5 available on port A
PortMask0=0x3F

[ADCPins]
ADC0=7
ADC1=6
ADC2=5
ADC3=3

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#define MX_CLK_SPEED %c\n#ifdef _BOOSTC\n#include <system.h>\n#endif\n#ifdef HI_TECH_C\n#include <pic.h>\n#endif\n"
MainStart="\nvoid main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n}\n\n"
IntStart="void MX_INTERRUPT_MACRO(void)\n{\n"
IntEnd="}\n\n"
Initialise="ansel = 0x00;\ncmcon0 = 0x07;\n"
IntInit="option_reg = 0xC0;\n\n"
InputCmdFull="trisio = trisio | %m;\n%o = gpio;\n"
InputCmdOneBit="trisio = trisio | %m;\n%o = ((gpio & %m) == %m);\n"
InputCmdMask="trisio = trisio | %m;\n%o = gpio & %m;\n"
OutputCmdFull="trisio = 0x00;\ngpio = %o;\n"
OutputCmdOneBit="trisio = trisio & %i;\nif (%o)\n\tgpio = (gpio & %i) | %m;\nelse\n\tgpio = gpio & %i;\n"
OutputCmdMask="trisio = trisio & %i;\ngpio = (gpio & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
DelayCmdUs="delay_us(%o);\n"
WdtDelayCmdS="Wdt_Delay_S(%o);\n"
WdtDelayCmdMs="Wdt_Delay_Ms(%o);\n"
InitialPortLetter="a"
ConfigData="#ifdef _BOOSTC\n#pragma DATA %a, %v\n#endif\n#ifdef HI_TECH_C\n__CONFIG(%v);\n#endif\n"
IntHandler="#ifndef MX_INTHANDLER_%r_%b\n#define MX_INTHANDLER_%r_%b\nif (ts_bit(%r, %b))\n{\n\tFCM_%n();\n\tcr_bit(%r, %b);\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif"

[Defines]
Define1=#define P12F683
Define2=#define FC_CAL_PIC
Define3=#define FC_USEGPIO
Define4=#define MX_ADC
Define5=#define MX_ADC_TYPE_5
Define6=#define MX_ADC_BITS_10
Define7=#define MX_EE
Define8=#define MX_EE_SIZE 256
Define9=#define MX_PWM
Define10=#define MX_PWM_CNT 1
Define11=#define MX_PWM_PSCA1
Define12=#define MX_PWM_PSCA4
Define13=#define MX_PWM_PSCA16
Define14=#define MX_PWM_1_PORT porta
Define15=#define MX_PWM_1_TRIS trisa
Define16=#define MX_PWM_1_PIN 2

[Interrupts]
;first 3 should always be 1=TMR0, 2=RB0INT, 3=PORTB
;any other interrupts need to also have this set: "st_bit(intcon,PEIE);\n"
GeneralInit="st_bit(intcon,GIE);\n"
Count=3
1=TMR0
3=PORTGPIO
2=GP2INT

[TMR0]
Name="TMR0"
HandlerCode="#ifndef MX_INTHANDLER_intcon_T0IF\n#define MX_INTHANDLER_intcon_T0IF\nif (ts_bit(intcon, T0IF) && ts_bit(intcon, T0IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(intcon, T0IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(intcon, T0IE);\n"
DisableCode="cr_bit(intcon, T0IE);\n"
OptCnt=3
PrescaleOpt=3
MaxTimerOverflow=256
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T0CKI pin"
Opt1_1Val="st_bit(option_reg,T0CS);\n"
Opt1_2="Internal clock (CLKO)"
Opt1_2Val="cr_bit(option_reg,T0CS);\n"
Opt2="Source Edge Select"
Opt2Cnt=2
Opt2_1="high-to-low transition on TMR0 Clock"
Opt2_1Val="st_bit(option_reg,T0SE);\n"
Opt2_2="low-to-high transition on TMR0 Clock"
Opt2_2Val="cr_bit(option_reg,T0SE);\n"
Opt3="Prescaler Rate"
Opt3Cnt=9
Opt3_1="1:1"
Opt3_1Val="option_reg = (option_reg & 0xF0) | 0x08;\n"
Opt3_2="1:2"
Opt3_2Val="option_reg = (option_reg & 0xF0) | 0x00;\n"
Opt3_3="1:4"
Opt3_3Val="option_reg = (option_reg & 0xF0) | 0x01;\n"
Opt3_4="1:8"
Opt3_4Val="option_reg = (option_reg & 0xF0) | 0x02;\n"
Opt3_5="1:16"
Opt3_5Val="option_reg = (option_reg & 0xF0) | 0x03;\n"
Opt3_6="1:32"
Opt3_6Val="option_reg = (option_reg & 0xF0) | 0x04;\n"
Opt3_7="1:64"
Opt3_7Val="option_reg = (option_reg & 0xF0) | 0x05;\n"
Opt3_8="1:128"
Opt3_8Val="option_reg = (option_reg & 0xF0) | 0x06;\n"
Opt3_9="1:256"
Opt3_9Val="option_reg = (option_reg & 0xF0) | 0x07;\n"

[PORTGPIO]
Name="PORT"
REMask=0x3F
FEMask=0x3F
ConfOpt=0x0C
HandlerCode="#ifndef MX_INTHANDLER_intcon_GPIF\n#define MX_INTHANDLER_intcon_GPIF\nchar mxtmp;\nif (ts_bit(intcon, GPIF) && ts_bit(intcon, GPIE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tmxtmp=gpio;\n\tcr_bit(intcon, GPIF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="ioc=%pA0v;\nst_bit(intcon, GPIE);\n"
DisableCode="cr_bit(intcon, GPIE);\n"
OptCnt=0


[GP2INT]
Name="INT"
REMask=0x04
FEMask=0x04
ConfOpt=0x03
EdgeOpt=0x01
HandlerCode="#ifndef MX_INTHANDLER_intcon_INTF\n#define MX_INTHANDLER_intcon_INTF\nif (ts_bit(intcon, INTF) && ts_bit(intcon, INTE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(intcon, INTF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(intcon, INTE);\n"
DisableCode="cr_bit(intcon, INTE);\n"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of INT"
Opt1_1Val="st_bit(option_reg,INTEDG);\n"
Opt1_2="falling edge of INT"
Opt1_2Val="cr_bit(option_reg,INTEDG);\n"