[Device]
Pins=28
Ports=3
ADCPins=5
ADCBits=8
ADCType=6
MaxClock=20000000
PrescalerBits=3
ClockDivider=4
ConfigAddress=0x2007
ConfigCount=1
PWMCount=1
UARTCount=0
EepromSize=0
HasAltPWM=0
Pwm2IsD4=0
FlowcodeProduct=PIC
UsesGpio=0
DefaultPackageType=0

[ICD]
ClockPort=1
ClockPin=6
DataPort=1
DataPin=7

[Pins]
Pin1 = "MCLR/VPP"
Pin2 = "RA0/AN0"
Pin3 = "RA1/AN1"
Pin4 = "RA2/AN2"
Pin5 = "RA3/AN3/VREF"
Pin6 = "RA4/T0CKI"
Pin7 = "RA5/AN4/SS"
Pin8 = "VSS"
Pin9 = "OSC1/CLKI"
Pin10 = "OSC2/CLKO"
Pin11 = "RC0/T1OSO/T1CKI"
Pin12 = "RC1/T1OSI"
Pin13 = "RC2/CCP1"
Pin14 = "RC3/SCK/SCL"
Pin15 = "RC4/SDI/SDA"
Pin16 = "RC5/SDO"
Pin17 = "RC6"
Pin18 = "RC7"
Pin19 = "VSS"
Pin20 = "VDD"
Pin21 = "RB0/INT"
Pin22 = "RB1"
Pin23 = "RB2"
Pin24 = "RB3"
Pin25 = "RB4"
Pin26 = "RB5"
Pin27 = "RB6/PGC"
Pin28 = "RB7/PGD"

[Ports]
PortPin2=0x0000
PortPin3=0x0001
PortPin4=0x0002
PortPin5=0x0003
PortPin6=0x0004
PortPin7=0x0005
PortPin11=0x0200
PortPin12=0x0201
PortPin13=0x0202
PortPin14=0x0203
PortPin15=0x0204
PortPin16=0x0205
PortPin17=0x0206
PortPin18=0x0207
PortPin21=0x0100
PortPin22=0x0101
PortPin23=0x0102
PortPin24=0x0103
PortPin25=0x0104
PortPin26=0x0105
PortPin27=0x0106
PortPin28=0x0107

[PortMasks]
;Only bits 0-5 available on port A
PortMask0=0x3F
PortMask1=0xFF
PortMask2=0xFF

[ADCPins]
ADC0=2
ADC1=3
ADC2=4
ADC3=5
ADC4=7

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#include <system.h>\n#pragma CLOCK_FREQ %c\n"
MainStart="void main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n}\n\n"
IntStart="void interrupt(void)\n{\n"
IntEnd="}\n\n"
Initialise="adcon1 = 0x07;\n"
IntInit="option_reg = 0xC0;\n\n"
InputCmdFull="tris%p = tris%p | %m;\n%o = port%p;\n"
InputCmdOneBit="tris%p = tris%p | %m;\n%o = ((port%p & %m) == %m);\n"
InputCmdMask="tris%p = tris%p | %m;\n%o = port%p & %m;\n"
OutputCmdFull="tris%p = 0x00;\nport%p = %o;\n"
OutputCmdOneBit="tris%p = tris%p & %i;\nif (%o)\n\tport%p = (port%p & %i) | %m;\nelse\n\tport%p = port%p & %i;\n"
OutputCmdMask="tris%p = tris%p & %i;\nport%p = (port%p & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
DelayCmdUs="delay_us(%o);\n"
WdtDelayCmdS="Wdt_Delay_S(%o);\n"
WdtDelayCmdMs="Wdt_Delay_Ms(%o);\n"
InitialPortLetter="a"
ConfigData="#pragma DATA %a, %v\n"
IntHandler="if (%r & (1 << %b))\n{\n\tFCM_%n();\n\tclear_bit(%r, %b);\n}\n"

[Defines]
Define1=#define P16F72
Define2=#define MX_SPI
Define3=#define MX_SPI_C
Define4=#define MX_SPI_SDI 4
Define5=#define MX_SPI_SDO 5
Define6=#define MX_SPI_SCK 3
Define7=#define MX_I2C
Define8=#define MX_MI2C
Define9=#define MX_I2C_C
Define10=#define MX_I2C_SDA 4
Define11=#define MX_I2C_SCL 3
Define12=#define MX_PWM
Define13=#define MX_PWM_CNT 1
Define14=#define MX_PWM_TRIS1 trisc
Define15=#define MX_PWM_1 2

[Interrupts]
;first 3 should always be 1=TMR0, 2=RB0INT, 3=PORTB
;any other interrupts need to also have this set: "intcon.PEIE=1;\n"
GeneralInit="intcon.GIE=1;\n"
Count=5
1=TMR0
2=RB0INT
3=PORTB
4=TMR1
5=TMR2

[TMR0]
;it is vital that this section remains exactly as-is (for all chips?)
Name="TMR0"
FlagReg=intcon
FlagBit=T0IF
EnReg=intcon
EnBit=T0IE
OptCnt=3
PrescaleOpt=3
MaxTimerOverflow=256
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T0CKI pin"
Opt1_1Val="option_reg.T0CS=1;\n"
Opt1_2="Internal clock (CLKO)"
Opt1_2Val="option_reg.T0CS=0;\n"
Opt2="Source Edge Select"
Opt2Cnt=2
Opt2_1="high-to-low transition on T0CKI"
Opt2_1Val="option_reg.T0SE=1;\n"
Opt2_2="low-to-high transition on T0CKI"
Opt2_2Val="option_reg.T0SE=0;\n"
Opt3="Prescaler Rate"
Opt3Cnt=9
Opt3_1="1:1"
Opt3_1Val="option_reg = (option_reg & 0xF0) | 0x08;\n"
Opt3_2="1:2"
Opt3_2Val="option_reg = (option_reg & 0xF0) | 0x00;\n"
Opt3_3="1:4"
Opt3_3Val="option_reg = (option_reg & 0xF0) | 0x01;\n"
Opt3_4="1:8"
Opt3_4Val="option_reg = (option_reg & 0xF0) | 0x02;\n"
Opt3_5="1:16"
Opt3_5Val="option_reg = (option_reg & 0xF0) | 0x03;\n"
Opt3_6="1:32"
Opt3_6Val="option_reg = (option_reg & 0xF0) | 0x04;\n"
Opt3_7="1:64"
Opt3_7Val="option_reg = (option_reg & 0xF0) | 0x05;\n"
Opt3_8="1:128"
Opt3_8Val="option_reg = (option_reg & 0xF0) | 0x06;\n"
Opt3_9="1:256"
Opt3_9Val="option_reg = (option_reg & 0xF0) | 0x07;\n"

[RB0INT]
Name="INT"
FlagReg=intcon
FlagBit=INTF
EnReg=intcon
EnBit=INTE
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of INT"
Opt1_1Val="option_reg.INTEDG=1;\n"
Opt1_2="falling edge of INT"
Opt1_2Val="option_reg.INTEDG=0;\n"

[PORTB]
Name="PORT"
FlagReg=intcon
FlagBit=RBIF
EnReg=intcon
EnBit=RBIE
OptCnt=0

[TMR1]
;NOTE: this osc is enabled and turned on as part of the Opt1 code
Name="TMR1"
FlagReg=pir1
FlagBit=TMR1IF
EnReg=pie1
EnBit=TMR1IE
OptCnt=2
PrescaleOpt=2
MaxTimerOverflow=65536
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T1CKI pin"
Opt1_1Val="intcon.PEIE=1;\nt1con.T1OSCEN=1;\nt1con.TMR1ON=1;\nt1con.TMR1CS=1;\n"
Opt1_2="Internal clock (Fosc/4)"
Opt1_2Val="intcon.PEIE=1;\nt1con.T1OSCEN=1;\nt1con.TMR1ON=1;\nt1con.TMR1CS=0;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="t1con = t1con & 0x0F;\n"
Opt2_2="1:2"
Opt2_2Val="t1con = (t1con & 0x0F) | 0x10;\n"
Opt2_3="1:4"
Opt2_3Val="t1con = (t1con & 0x0F) | 0x20;\n"
Opt2_4="1:8"
Opt2_4Val="t1con = (t1con & 0x0F) | 0x30;\n"

[TMR2]
;it is vital that this section remains exactly as-is (for all chips?)
Name="TMR2"
FlagReg=pir1
FlagBit=TMR2IF
EnReg=pie1
EnBit=TMR2IE
OptCnt=3
PrescaleOpt=1
PostScaleOpt=2
RolloverOpt=3
MaxTimerOverflow=256
Opt1="Prescaler Rate"
Opt1Cnt=3
Opt1_1="1:1"
Opt1_1Val="intcon.PEIE=1;\nt2con.T2CKPS0=0;\nt2con.T2CKPS1=0;\nt2con.TMR2ON=1;\n"
Opt1_2="1:4"
Opt1_2Val="intcon.PEIE=1;\nt2con.T2CKPS0=1;\nt2con.T2CKPS1=0;\nt2con.TMR2ON=1;\n"
Opt1_3="1:16"
Opt1_3Val="intcon.PEIE=1;\nt2con.T2CKPS0=0;\nt2con.T2CKPS1=1;\nt2con.TMR2ON=1;\n"
Opt2="Postscaler Rate"
Opt2Cnt=16
Opt2_1="1:1"
Opt2_1Val="t2con = t2con & 0x07;\n"
Opt2_2="1:2"
Opt2_2Val="t2con = (t2con & 0x07) | 0x08;\n"
Opt2_3="1:3"
Opt2_3Val="t2con = (t2con & 0x07) | 0x10;\n"
Opt2_4="1:4"
Opt2_4Val="t2con = (t2con & 0x07) | 0x18;\n"
Opt2_5="1:5"
Opt2_5Val="t2con = (t2con & 0x07) | 0x20;\n"
Opt2_6="1:6"
Opt2_6Val="t2con = (t2con & 0x07) | 0x28;\n"
Opt2_7="1:7"
Opt2_7Val="t2con = (t2con & 0x07) | 0x30;\n"
Opt2_8="1:8"
Opt2_8Val="t2con = (t2con & 0x07) | 0x38;\n"
Opt2_9="1:9"
Opt2_9Val="t2con = (t2con & 0x07) | 0x40;\n"
Opt2_10="1:10"
Opt2_10Val="t2con = (t2con & 0x07) | 0x48;\n"
Opt2_11="1:11"
Opt2_11Val="t2con = (t2con & 0x07) | 0x50;\n"
Opt2_12="1:12"
Opt2_12Val="t2con = (t2con & 0x07) | 0x58;\n"
Opt2_13="1:13"
Opt2_13Val="t2con = (t2con & 0x07) | 0x60;\n"
Opt2_14="1:14"
Opt2_14Val="t2con = (t2con & 0x07) | 0x68;\n"
Opt2_15="1:15"
Opt2_15Val="t2con = (t2con & 0x07) | 0x70;\n"
Opt2_16="1:16"
Opt2_16Val="t2con = (t2con & 0x07) | 0x78;\n"
Opt3="Rollover Value"
Opt3Cnt=5
Opt3_1="256"
Opt3_1Val="pr2=%d-1;\n"
Opt3_2="128"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="64"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="32"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="16"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"