[Device]
Pins=28
Ports=5
ADCPins=13
ADCBits=10
MaxClock=41000000
PrescalerBits=3
ClockDivider=4
TimerOverflow=256
ConfigAddress=0x300000
ConfigCount=14
PortBits=8
PWMCount=2
UARTCount=1
SPICount=1
I2CCount=1
CANCount=0
ComparatorCount=2
TimerCount8=1
TimerCount16=3
EepromSize=1024
HasAltPWM=2
FlowcodeProduct=PIC
DefaultPackageType=0
FlashSize=65536
RamSize=3986

[ICD]
ClockPort=1
ClockPin=6
DataPort=1
DataPin=7


[Pins]
Pin1 = "MCLR/VPP/RE3"
Pin2 = "RA0/AN0"
Pin3 = "RA1/AN1"
Pin4 = "RA2/AN2/VREF-/CVREF"
Pin5 = "RA3/AN3/VREF+"
Pin6 = "RA4/T0CKI/C1OUT"
Pin7 = "RA5/AN4/SS/HLVDIN/C2OUT"
Pin8 = "VSS"
Pin9 = "OSC1/CLKI/RA7"
Pin10 = "OSC2/CLKO/RA6"
Pin11 = "RC0/T1OSO/T3CKI"
Pin12 = "RC1/T1OSI/CCP2"
Pin13 = "RC2/CCP1"
Pin14 = "RC3/SCK/SCL"
Pin15 = "RC4/SDI/SDA"
Pin16 = "RC5/SDO"
Pin17 = "RC6/TX/CK"
Pin18 = "RC7/RX/DT"
Pin19 = "VSS"
Pin20 = "VDD"
Pin21 = "RB0/AN12/INT0/FLT0"
Pin22 = "RB1/AN10/INT1"
Pin23 = "RB2/AN8/INT2"
Pin24 = "RB3/AN9/CCP2"
Pin25 = "RB4/AN11/KBI0"
Pin26 = "RB5/KBI1/PGM"
Pin27 = "RB6/KBI2/PGC"
Pin28 = "RB7/KBI3/PGD"

[Ports]
PortPin1=0x0403
PortPin2=0x0000
PortPin3=0x0001
PortPin4=0x0002
PortPin5=0x0003
PortPin6=0x0004
PortPin7=0x0005
PortPin9=0x0007
PortPin10=0x0006
PortPin11=0x0200
PortPin12=0x0201
PortPin13=0x0202
PortPin14=0x0203
PortPin15=0x0204
PortPin16=0x0205
PortPin17=0x0206
PortPin18=0x0207
PortPin21=0x0100
PortPin22=0x0101
PortPin23=0x0102
PortPin24=0x0103
PortPin25=0x0104
PortPin26=0x0105
PortPin27=0x0106
PortPin28=0x0107

[PortMasks]
PortMask0=0xFF
PortMask1=0xFF
PortMask2=0xFF
PortMask3=0x00
PortMask4=0x08

[ADCPins]
ADC0=2
ADC1=3
ADC2=4
ADC3=5
ADC4=7
ADC5=0
ADC6=0
ADC7=0
ADC8=23
ADC9=24
ADC10=22
ADC11=25
ADC12=21

[ADC_ConvSpeed]
Count=7
Opt1=Fosc / 2
Opt1_Val=0
Opt2=Fosc / 8
Opt2_Val=1
Opt3=Fosc / 32
Opt3_Val=2
Opt4=FRC
Opt4_Val=3
Opt5=Fosc / 4
Opt5_Val=4
Opt6=Fosc / 16
Opt6_Val=5
Opt7=Fosc / 64
Opt7_Val=6

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#define MX_CLK_SPEED %c\n#ifdef _BOOSTC\n#include <system.h>\n#endif\n#ifdef HI_TECH_C\n#include <pic18.h>\n#endif\n"
MainStart="void main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n}\n\n"
IntStart="void MX_INTERRUPT_MACRO(void)\n{\n"
IntEnd="}\n\n"
Initialise="adcon1 = 0x0F;\n"
IntInit="\n\n"
InputCmdFull="tris%p = tris%p | %m;\n%o = port%p;\n"
InputCmdOneBit="tris%p = tris%p | %m;\n%o = ((port%p & %m) == %m);\n"
InputCmdMask="tris%p = tris%p | %m;\n%o = port%p & %m;\n"
OutputCmdFull="tris%p = 0x00;\nport%p = %o;\n"
OutputCmdOneBit="tris%p = tris%p & %i;\nif (%o)\n\tport%p = (port%p & %i) | %m;\nelse\n\tport%p = port%p & %i;\n"
OutputCmdMask="tris%p = tris%p & %i;\nport%p = (port%p & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
DelayCmdUs="delay_us(%o);\n"
WdtDelayCmdS="Wdt_Delay_S(%o);\n"
WdtDelayCmdMs="Wdt_Delay_Ms(%o);\n"
InitialPortLetter="a"
ConfigData="#ifdef _BOOSTC\n#pragma DATA %a, %v\n#endif\n#ifdef _HI_TECH_C\n%C__CONFIG(%A, %V);\n#endif\n"
IntHandler="#ifndef MX_INTHANDLER_%r_%b\n#define MX_INTHANDLER_%r_%b\nif (%r & (1 << %b))\n{\n\tFCM_%n();\n\tclear_bit(%r, %b);\n}\n\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"

[Defines]
Define1=#define P18F2620
Define2=#define FC_CAL_PIC
Define3=#define MX_ADC
Define4=#define MX_ADC_TYPE_13
Define5=#define MX_ADC_BITS_10
Define6=#define MX_EE
Define7=#define MX_EE_TYPE3
Define8=#define MX_EE_SIZE 1024
Define9=#define MX_SPI_1
Define10=#define MX_SPI_1_MISO_PORT portc
Define11=#define MX_SPI_1_MISO_TRIS trisc
Define12=#define MX_SPI_1_MISO_PIN 4
Define13=#define MX_SPI_1_MOSI_PORT portc
Define14=#define MX_SPI_1_MOSI_TRIS trisc
Define15=#define MX_SPI_1_MOSI_PIN 5
Define16=#define MX_SPI_1_CLK_PORT portc
Define17=#define MX_SPI_1_CLK_TRIS trisc
Define18=#define MX_SPI_1_CLK_PIN 3
Define19=#define MX_SPI_1_SS_PORT porta
Define20=#define MX_SPI_1_SS_TRIS trisa
Define21=#define MX_SPI_1_SS_PIN 5
Define22=#define MX_UART_1
Define23=#define MX_UART_1_TX_PORT portc
Define24=#define MX_UART_1_TX_TRIS trisc
Define25=#define MX_UART_1_TX_PIN 6
Define26=#define MX_UART_1_RX_PORT portc
Define27=#define MX_UART_1_RX_TRIS trisc
Define28=#define MX_UART_1_RX_PIN 7
Define29=#define MX_I2C
Define30=#define MX_MI2C
Define31=#define MX_I2C_1
Define32=#define MX_I2C_1_SDA_PORT portc
Define33=#define MX_I2C_1_SDA_TRIS trisc
Define34=#define MX_I2C_1_SDA_PIN 4
Define35=#define MX_I2C_1_SCL_PORT portc
Define36=#define MX_I2C_1_SCL_TRIS trisc
Define37=#define MX_I2C_1_SCL_PIN 3
Define38=#define MX_PWM
Define39=#define MX_PWM_CNT 2
Define40=#define MX_PWM_PSCA1
Define41=#define MX_PWM_PSCA4
Define42=#define MX_PWM_PSCA16
Define43=#define MX_PWM_1_PORT portc
Define44=#define MX_PWM_1_TRIS trisc
Define45=#define MX_PWM_1_PIN 2
Define46=#define MX_PWM_2_PORT portc
Define47=#define MX_PWM_2_TRIS trisc
Define48=#define MX_PWM_2_PIN 1
Define49=#define MX_PWM_2_PORT_A portb
Define50=#define MX_PWM_2_TRIS_A trisb
Define51=#define MX_PWM_2_PIN_A 3

[Interrupts]
;first 3 should always be 1=TMR0, 2=RB0INT, 3=PORTB
;any other interrupts need to also have this set: "st_bit(intcon, PEIE);\n"
GeneralInit="st_bit(intcon, GIE);\n"
Count=9
1=TMR0
2=RB0INT
3=PORTB
4=TMR1
5=RB1INT
6=RB2INT
7=RXINT
8=TMR2
9=TMR3

[TMR0]
Name="TMR0"
HandlerCode="#ifndef MX_INTHANDLER_intcon_TMR0IF\n#define MX_INTHANDLER_intcon_TMR0IF\nif (ts_bit(intcon, TMR0IF) && ts_bit(intcon, TMR0IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\t\n\tFCM_%n();\n\tcr_bit(intcon, TMR0IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(intcon, TMR0IE);\n"
DisableCode="cr_bit(intcon, TMR0IE);\n"
OptCnt=3
PrescaleOpt=3
MaxTimerOverflow=256
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T0CKI pin"
Opt1_1Val="st_bit(t0con, T0CS);\n"
Opt1_2="Internal clock (CLKO)"
Opt1_2Val="cr_bit(t0con, T0CS);\n"
Opt2="Source Edge Select"
Opt2Cnt=2
Opt2_1="high-to-low transition on TMR0 Clock"
Opt2_1Val="st_bit(t0con, T0SE);\n"
Opt2_2="low-to-high transition on TMR0 Clock"
Opt2_2Val="cr_bit(t0con, T0SE);\n"
Opt3="Prescaler Rate"
Opt3Cnt=9
Opt3_1="1:1"
Opt3_1Val="t0con = (t0con & 0xF0) | 0x08;\n"
Opt3_2="1:2"
Opt3_2Val="t0con = (t0con & 0xF0) | 0x00;\n"
Opt3_3="1:4"
Opt3_3Val="t0con = (t0con & 0xF0) | 0x01;\n"
Opt3_4="1:8"
Opt3_4Val="t0con = (t0con & 0xF0) | 0x02;\n"
Opt3_5="1:16"
Opt3_5Val="t0con = (t0con & 0xF0) | 0x03;\n"
Opt3_6="1:32"
Opt3_6Val="t0con = (t0con & 0xF0) | 0x04;\n"
Opt3_7="1:64"
Opt3_7Val="t0con = (t0con & 0xF0) | 0x05;\n"
Opt3_8="1:128"
Opt3_8Val="t0con = (t0con & 0xF0) | 0x06;\n"
Opt3_9="1:256"
Opt3_9Val="t0con = (t0con & 0xF0) | 0x07;\n"

[RB0INT]
Name="RB0/INT0"
REMask=0x00,0x01
FEMask=0x00,0x01
ConfOpt=0x03
EdgeOpt=0x01
HandlerCode="#ifndef MX_INTHANDLER_intcon_INT0IF\n#define MX_INTHANDLER_intcon_INT0IF\nif (ts_bit(intcon, INT0IF) && ts_bit(intcon, INT0IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\n\tFCM_%n();\n\tcr_bit(intcon, INT0IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(intcon, INT0IE);\n"
DisableCode="cr_bit(intcon, INT0IE);\n"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB0/INT0"
Opt1_1Val="st_bit(intcon2, INTEDG0);\n"
Opt1_2="falling edge of RB0/INT0"
Opt1_2Val="cr_bit(intcon2, INTEDG0);\n"

[PORTB]
Name="PORT"
REMask=0x00,0xF0
FEMask=0x00,0xF0
ConfOpt=0x04
HandlerCode="#ifndef MX_INTHANDLER_intcon_RBIF\n#define MX_INTHANDLER_intcon_RBIF\nchar mxtmp;\nif (ts_bit(intcon, RBIF) && ts_bit(intcon, RBIE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\n\tFCM_%n();\n\tmxtmp=portb;\n\tcr_bit(intcon, RBIF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(intcon, RBIE);\n"
DisableCode="cr_bit(intcon, RBIE);\n"
OptCnt=0

[TMR1]
Name="TMR1"
HandlerCode="#ifndef MX_INTHANDLER_pir1_TMR1IF\n#define MX_INTHANDLER_pir1_TMR1IF\nif (ts_bit(pir1, TMR1IF) && ts_bit(pie1, TMR1IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\n\tFCM_%n();\n\tcr_bit(pir1, TMR1IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(pie1, TMR1IE);\n"
DisableCode="cr_bit(pie1, TMR1IE);\n"
OptCnt=2
PrescaleOpt=2
MaxTimerOverflow=65536
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T1CKI pin"
Opt1_1Val="st_bit(intcon, PEIE);\nst_bit(t1con, T1OSCEN);\nst_bit(t1con, TMR1ON);\nst_bit(t1con, TMR1CS);\n"
Opt1_2="Internal clock (Fosc/4)"
Opt1_2Val="st_bit(intcon, PEIE);\nst_bit(t1con, T1OSCEN);\nst_bit(t1con, TMR1ON);\ncr_bit(t1con, TMR1CS);\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="t1con = 0b10000111;\n"
Opt2_2="1:2"
Opt2_2Val="t1con = (t1con & 0x0F) | 0x10;\n"
Opt2_3="1:4"
Opt2_3Val="t1con = (t1con & 0x0F) | 0x20;\n"
Opt2_4="1:8"
Opt2_4Val="t1con = (t1con & 0x0F) | 0x30;\n"

[RB1INT]
Name="RB1/INT1"
REMask=0x00,0x02
FEMask=0x00,0x02
ConfOpt=0x03
EdgeOpt=0x01
HandlerCode="#ifndef MX_INTHANDLER_intcon3_INT1IF\n#define MX_INTHANDLER_intcon3_INT1IF\nif (ts_bit(intcon3, INT1IF) && ts_bit(intcon3, INT1IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\n\tFCM_%n();\n\tcr_bit(intcon3, INT1IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(intcon3, INT1IE);\n"
DisableCode="cr_bit(intcon3, INT1IE);\n"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB1/INT1"
Opt1_1Val="st_bit(intcon2, INTEDG1);\n"
Opt1_2="falling edge of RB1/INT1"
Opt1_2Val="cr_bit(intcon2, INTEDG1);\n"

[RB2INT]
Name="RB2/INT2"
REMask=0x00,0x04
FEMask=0x00,0x04
ConfOpt=0x03
EdgeOpt=0x01
HandlerCode="#ifndef MX_INTHANDLER_intcon3_INT2IF\n#define MX_INTHANDLER_intcon3_INT2IF\nif (ts_bit(intcon3, INT2IF) && ts_bit(intcon3, INT2IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\n\tFCM_%n();\n\tcr_bit(intcon3, INT2IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(intcon3, INT2IE);\n"
DisableCode="cr_bit(intcon3, INT2IE);\n"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB2/INT2"
Opt1_1Val="st_bit(intcon2, INTEDG2);\n"
Opt1_2="falling edge of RB2/INT2"
Opt1_2Val="cr_bit(intcon2, INTEDG2);\n"

[RXINT]
Name="RXINT"
HandlerCode="#ifndef MX_INTHANDLER_pir1_RCIF\n#define MX_INTHANDLER_pir1_RCIF\nif (ts_bit(pir1, RCIF) && ts_bit(pie1, RCIE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\n\tFCM_%n();\n\tcr_bit(pir1, RCIF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif"
EnableCode="st_bit(pie1, RCIE);\n"
DisableCode="cr_bit(pie1, RCIE);\n"
OptCnt=0

[TMR2]
Name="TMR2"
HandlerCode="#ifndef MX_INTHANDLER_pir1_TMR2IF\n#define MX_INTHANDLER_pir1_TMR2IF\nif (ts_bit(pir1, TMR2IF) && ts_bit(pie1, TMR2IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\n\tFCM_%n();\n\tcr_bit(pir1, TMR2IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif"
EnableCode="st_bit(pie1, TMR2IE);\n"
DisableCode="cr_bit(pie1, TMR2IE);\n"
OptCnt=3
PrescaleOpt=1
PostScaleOpt=2
RolloverOpt=3
MaxTimerOverflow=256
Opt1="Prescaler Rate"
Opt1Cnt=3
Opt1_1="1:1"
Opt1_1Val="st_bit(intcon, PEIE);\ncr_bit(t2con, T2CKPS0);\ncr_bit(t2con, T2CKPS1);\nst_bit(t2con, TMR2ON);\n"
Opt1_2="1:4"
Opt1_2Val="st_bit(intcon, PEIE);\nst_bit(t2con, T2CKPS0);\ncr_bit(t2con, T2CKPS1);\nst_bit(t2con, TMR2ON);\n"
Opt1_3="1:16"
Opt1_3Val="st_bit(intcon, PEIE);\ncr_bit(t2con, T2CKPS0);\nst_bit(t2con, T2CKPS1);\nst_bit(t2con, TMR2ON);\n"
Opt2="Postscaler Rate"
Opt2Cnt=16
Opt2_1="1:1"
Opt2_1Val="t2con = t2con & 0x07;\n"
Opt2_2="1:2"
Opt2_2Val="t2con = (t2con & 0x07) | 0x08;\n"
Opt2_3="1:3"
Opt2_3Val="t2con = (t2con & 0x07) | 0x10;\n"
Opt2_4="1:4"
Opt2_4Val="t2con = (t2con & 0x07) | 0x18;\n"
Opt2_5="1:5"
Opt2_5Val="t2con = (t2con & 0x07) | 0x20;\n"
Opt2_6="1:6"
Opt2_6Val="t2con = (t2con & 0x07) | 0x28;\n"
Opt2_7="1:7"
Opt2_7Val="t2con = (t2con & 0x07) | 0x30;\n"
Opt2_8="1:8"
Opt2_8Val="t2con = (t2con & 0x07) | 0x38;\n"
Opt2_9="1:9"
Opt2_9Val="t2con = (t2con & 0x07) | 0x40;\n"
Opt2_10="1:10"
Opt2_10Val="t2con = (t2con & 0x07) | 0x48;\n"
Opt2_11="1:11"
Opt2_11Val="t2con = (t2con & 0x07) | 0x50;\n"
Opt2_12="1:12"
Opt2_12Val="t2con = (t2con & 0x07) | 0x58;\n"
Opt2_13="1:13"
Opt2_13Val="t2con = (t2con & 0x07) | 0x60;\n"
Opt2_14="1:14"
Opt2_14Val="t2con = (t2con & 0x07) | 0x68;\n"
Opt2_15="1:15"
Opt2_15Val="t2con = (t2con & 0x07) | 0x70;\n"
Opt2_16="1:16"
Opt2_16Val="t2con = (t2con & 0x07) | 0x78;\n"
Opt3="Rollover Value"
Opt3Cnt=5
Opt3_1="256"
Opt3_1Val="pr2=%d-1;\n"
Opt3_2="128"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="64"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="32"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="16"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"

[TMR3]
Name="TMR3"
HandlerCode="#ifndef MX_INTHANDLER_pir2_TMR3IF\n#define MX_INTHANDLER_pir2_TMR3IF\nif (ts_bit(pir2, TMR3IF) && ts_bit(pie2, TMR3IE))\n{\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 1;\n\t#endif\n\tFCM_%n();\n\tcr_bit(pir2, TMR3IF);\n\t#ifdef USE_FLOWCODE_ICD\n\t\textern char ICD_Interrupt_Enable = 0;\n\t#endif\t\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="st_bit(pie2, TMR3IE);\n"
DisableCode="cr_bit(pie2, TMR3IE);\n"
OptCnt=2
PrescaleOpt=2
MaxTimerOverflow=65536
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T3CKI pin"
Opt1_1Val="st_bit(intcon, PEIE);\nst_bit(t3con, TMR3ON);\nst_bit(t3con, TMR3CS);\n"
Opt1_2="Internal clock (Fosc/4)"
Opt1_2Val="st_bit(intcon, PEIE);\nst_bit(t3con, TMR3ON);\ncr_bit(t3con, TMR3CS);\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="t3con = t3con & 0x0F;\n"
Opt2_2="1:2"
Opt2_2Val="t3con = (t3con & 0x0F) | 0x10;\n"
Opt2_3="1:4"
Opt2_3Val="t3con = (t3con & 0x0F) | 0x20;\n"
Opt2_4="1:8"
Opt2_4Val="t3con = (t3con & 0x0F) | 0x30;\n"