[Device]
Pins=40
Ports=5
ADCPins=13
ADCBits=10
ADCType=13
MaxClock=48000000
PrescalerBits=3
ClockDivider=4
TimerOverflow=256
ConfigAddress=0x300000
ConfigCount=14
PWMCount=2
UARTCount=1
EepromSize=256
HasAltPWM=2
Pwm2IsD4=0
ChipName=18F4455
ConfigOverride=1
ClockOverrideValue=48000000
ProgrammerOverride=tools/ECIOprog/ECIOprog.exe
ProgSwitchesOverride=-nogui "%f.hex"
ExtraLinkerParams=-rb 0x800
FlowcodeProduct=PIC
DefaultPackageType=0

[ICD]
ClockPort=2
ClockPin=4
DataPort=4
DataPin=2

[Config]
0=0x20
1=0x0E
2=0x3E
3=0x1E
4=0x00
5=0x81
6=0x81
7=0x00
8=0x0F
9=0x80
10=0x0F
11=0xA0
12=0x0F
13=0x00

[Pins]
Pin1 = "VDD_OUT"
Pin2 = "GND"
Pin3 = "MCLR"
Pin4 = "RA0/AN0"
Pin5 = "RA1/AN1"
Pin6 = "RA2/AN2/VREF-/CVREF"
Pin7 = "RA3/AN3/VREF+"
Pin8 = "RA4/T0CKI/C1OUT/RCV"
Pin9 = "RA5/AN4/SS/HLVDIN/C2OUT"
Pin10 = "N/C"
Pin11 = "N/C"
Pin12 = "N/C"
Pin13 = "RD0/SPP0"
Pin14 = "RD1/SPP1"
Pin15 = "RD2/SPP2"
Pin16 = "RD3/SPP3"
Pin17 = "RD4/SPP4"
Pin18 = "RD5/SPP5/P1B"
Pin19 = "RD6/SPP6/P1C"
Pin20 = "RD7/SPP7/P1D"
Pin21 = "N/C"
Pin22 = "N/C"
Pin23 = "RE0/AN5/CK1SPP"
Pin24 = "RE1/AN6/CK2SPP"
Pin25 = "RE2/AN7/OESPP"
Pin26 = "GND"
Pin27 = "RC0/T1OSO"
Pin28 = "RC1/T1OSI/CCP2B"
Pin29 = "RC2/CCP1/P1A"
Pin30 = "RC6/TX/CK"
Pin31 = "RC7/RX/DT/SDO"
Pin32 = "RB0/AN12/INT0/FLT0/SDI/SDA"
Pin33 = "RB1/AN10/INT1/SCK/SCL"
Pin34 = "RB2/AN8/INT2/VMO"
Pin35 = "RB3/AN9/CCP2/VPO"
Pin36 = "RB4/AN11/KBI0/CSSPP"
Pin37 = "RB5/KBI1/PGM"
Pin38 = "RB6/KBI2/PGC"
Pin39 = "RB7/KBI3/PGD"
Pin40 = "VDD_IN"

[Ports]
PortPin4=0x0000
PortPin5=0x0001
PortPin6=0x0002
PortPin7=0x0003
PortPin8=0x0004
PortPin9=0x0005
PortPin13=0x0300
PortPin14=0x0301
PortPin15=0x0302
PortPin16=0x0303
PortPin17=0x0304
PortPin18=0x0305
PortPin19=0x0306
PortPin20=0x0307
PortPin23=0x0400
PortPin24=0x0401
PortPin25=0x0402
PortPin27=0x0200
PortPin28=0x0201
PortPin29=0x0202
PortPin30=0x0206
PortPin31=0x0207
PortPin32=0x0100
PortPin33=0x0101
PortPin34=0x0102
PortPin35=0x0103
PortPin36=0x0104
PortPin37=0x0105
PortPin38=0x0106
PortPin39=0x0107

[PortMasks]
PortMask0=0x3F
PortMask1=0xFF
PortMask2=0xF7
PortMask3=0xFF
PortMask4=0x0F

[ADCPins]
ADC0=2
ADC1=3
ADC2=4
ADC3=5
ADC4=7
ADC5=8
ADC6=9
ADC7=10
ADC8=35
ADC9=36
ADC10=34
ADC11=37
ADC12=33

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#include <system.h>\n#pragma CLOCK_FREQ %c\n"
MainStart="void main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n}\n\n"
IntStart="void interrupt(void)\n{\n"
IntEnd="}\n\n"
Initialise="adcon1 = 0x0F;\n\tucfg = 0x08;\n"
IntInit="\n\n"
InputCmdFull="tris%p = tris%p | %m;\n%o = port%p;\n"
InputCmdOneBit="tris%p = tris%p | %m;\n%o = ((port%p & %m) == %m);\n"
InputCmdMask="tris%p = tris%p | %m;\n%o = port%p & %m;\n"
OutputCmdFull="tris%p = 0x00;\nport%p = %o;\n"
OutputCmdOneBit="tris%p = tris%p & %i;\nif (%o)\n\tport%p = (port%p & %i) | %m;\nelse\n\tport%p = port%p & %i;\n"
OutputCmdMask="tris%p = tris%p & %i;\nport%p = (port%p & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
DelayCmdUs="delay_us(%o);\n"
WdtDelayCmdS="Wdt_Delay_S(%o);\n"
WdtDelayCmdMs="Wdt_Delay_Ms(%o);\n"
InitialPortLetter="a"
ConfigData="#pragma DATA %a, %v\n"
IntHandler="if (%r & (1 << %b))\n{\n\tFCM_%n();\n\tclear_bit(%r, %b);\n}\n"

[Defines]
Define1=#define P18F4455
Define2=#define MX_EE
Define3=#define MX_EE_TYPE3
Define4=#define MX_EE_SIZE 256
Define5=#define MX_SPI
Define6=#define MX_SPI_BCB
Define7=#define MX_SPI_SDI 0
Define8=#define MX_SPI_SDO 7
Define9=#define MX_SPI_SCK 1
Define10=#define MX_UART
Define11=#define MX_UART_C
Define12=#define MX_UART_TX 6
Define13=#define MX_UART_RX 7
Define14=#define MX_I2C
Define15=#define MX_MI2C
Define16=#define MX_I2C_B
Define17=#define MX_I2C_SDA 0
Define18=#define MX_I2C_SCL 1
Define19=#define MX_PWM
Define20=#define MX_PWM_CNT 2
Define21=#define MX_PWM_TRIS1 trisc
Define22=#define MX_PWM_1 2
Define23=#define MX_PWM_TRIS2 trisc
Define24=#define MX_PWM_2 1
Define25=#define MX_PWM_TRIS2a trisb
Define26=#define MX_PWM_2a 3
Define27=#define MX_USB_TYPE1

[Interrupts]
;first 3 should always be 1=TMR0, 2=RB0INT, 3=PORTB
;any other interrupts need to also have this set: "intcon.PEIE=1;\n"
GeneralInit="intcon.GIE=1;\n"
Count=9
1=TMR0
2=RB0INT
3=PORTB
4=TMR1
5=RB1INT
6=RB2INT
7=USBINT
8=RXINT
9=TMR2

[TMR0]
Name="TMR0"
FlagReg=intcon
FlagBit=TMR0IF
HandlerCode="if ((intcon & (1 << TMR0IF)) && (intcon & (1 << TMR0IE)))\n{\n\tFCM_%n();\n\tclear_bit(intcon, TMR0IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=intcon
EnBit=TMR0IE
OptCnt=3
PrescaleOpt=3
MaxTimerOverflow=256
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T0CKI pin"
Opt1_1Val="t0con.T0CS=1;\n"
Opt1_2="Internal clock (CLKO)"
Opt1_2Val="t0con.T0CS=0;\n"
Opt2="Source Edge Select"
Opt2Cnt=2
Opt2_1="high-to-low transition on T0CKI"
Opt2_1Val="t0con.T0SE=1;\n"
Opt2_2="low-to-high transition on T0CKI"
Opt2_2Val="t0con.T0SE=0;\n"
Opt3="Prescaler Rate"
Opt3Cnt=9
Opt3_1="1:1"
Opt3_1Val="t0con = (t0con & 0xF0) | 0x08;\n"
Opt3_2="1:2"
Opt3_2Val="t0con = (t0con & 0xF0) | 0x00;\n"
Opt3_3="1:4"
Opt3_3Val="t0con = (t0con & 0xF0) | 0x01;\n"
Opt3_4="1:8"
Opt3_4Val="t0con = (t0con & 0xF0) | 0x02;\n"
Opt3_5="1:16"
Opt3_5Val="t0con = (t0con & 0xF0) | 0x03;\n"
Opt3_6="1:32"
Opt3_6Val="t0con = (t0con & 0xF0) | 0x04;\n"
Opt3_7="1:64"
Opt3_7Val="t0con = (t0con & 0xF0) | 0x05;\n"
Opt3_8="1:128"
Opt3_8Val="t0con = (t0con & 0xF0) | 0x06;\n"
Opt3_9="1:256"
Opt3_9Val="t0con = (t0con & 0xF0) | 0x07;\n"

[RB0INT]
Name="RB0/INT0"
FlagReg=intcon
FlagBit=INT0IF
HandlerCode="if ((intcon & (1 << INT0IF)) && (intcon & (1 << INT0IE)))\n{\n\tFCM_%n();\n\tclear_bit(intcon, INT0IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=intcon
EnBit=INT0IE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB0/INT0"
Opt1_1Val="intcon2.INTEDG0=1;\n"
Opt1_2="falling edge of RB0/INT0"
Opt1_2Val="intcon2.INTEDG0=0;\n"

[PORTB]
Name="PORT"
FlagReg=intcon
FlagBit=RBIF
HandlerCode="if ((intcon & (1 << RBIF)) && (intcon & (1 << RBIE)))\n{\n\tFCM_%n();\n\tclear_bit(intcon, RBIF);\n}\n"
UseExplicitHandlerCode=1
EnReg=intcon
EnBit=RBIE
OptCnt=0
TmrOpt=0

[TMR1]
Name="TMR1"
FlagReg=pir1
FlagBit=TMR1IF
HandlerCode="if ((pir1 & (1 << TMR1IF)) && (pie1 & (1 << TMR1IE)))\n{\n\tFCM_%n();\n\tclear_bit(pir1, TMR1IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=pie1
EnBit=TMR1IE
OptCnt=2
PrescaleOpt=2
MaxTimerOverflow=65536
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T1CKI pin"
Opt1_1Val="intcon.PEIE=1;\nt1con.T1OSCEN=1;\nt1con.TMR1ON=1;\nt1con.TMR1CS=1;\n"
Opt1_2="Internal clock (Fosc/4)"
Opt1_2Val="intcon.PEIE=1;\nt1con.T1OSCEN=1;\nt1con.TMR1ON=1;\nt1con.TMR1CS=0;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="t1con = t1con & 0x0F;\n"
Opt2_2="1:2"
Opt2_2Val="t1con = (t1con & 0x0F) | 0x10;\n"
Opt2_3="1:4"
Opt2_3Val="t1con = (t1con & 0x0F) | 0x20;\n"
Opt2_4="1:8"
Opt2_4Val="t1con = (t1con & 0x0F) | 0x30;\n"

[RB1INT]
Name="RB1/INT1"
FlagReg=intcon3
FlagBit=INT1IF
HandlerCode="if ((intcon3 & (1 << INT1IF)) && (intcon3 & (1 << INT1IE)))\n{\n\tFCM_%n();\n\tclear_bit(intcon3, INT1IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=intcon3
EnBit=INT1IE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB1/INT1"
Opt1_1Val="intcon2.INTEDG1=1;\n"
Opt1_2="falling edge of RB1/INT1"
Opt1_2Val="intcon2.INTEDG1=0;\n"

[RB2INT]
Name="RB2/INT2"
FlagReg=intcon3
FlagBit=INT2IF
HandlerCode="if ((intcon3 & (1 << INT2IF)) && (intcon3 & (1 << INT2IE)))\n{\n\tFCM_%n();\n\tclear_bit(intcon3, INT2IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=intcon3
EnBit=INT2IE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB2/INT2"
Opt1_1Val="intcon2.INTEDG2=1;\n"
Opt1_2="falling edge of RB2/INT2"
Opt1_2Val="intcon2.INTEDG2=0;\n"

[USBINT]
Name="USBINT"
FlagReg=pir2
FlagBit=USBIF
HandlerCode="if ((pir2 & (1 << USBIF)) && (pie2 & (1 << USBIE)))\n{\n\tFCM_%n();\n\tclear_bit(pir2, USBIF);\n}\n"
UseExplicitHandlerCode=1
EnReg=pie2
EnBit=USBIE
OptCnt=0
TmrOpt=0

[RXINT]
Name="RXINT"
FlagReg=pir1
FlagBit=RCIF
HandlerCode="if ((pir1 & (1 << RCIF)) && (pie1 & (1 << RCIE)))\n{\n\tFCM_%n();\n\tclear_bit(pir1, RCIF);\n}\n"
UseExplicitHandlerCode=1
EnReg=pie1
EnBit=RCIE
OptCnt=0
TmrOpt=0

[TMR2]
Name="TMR2"
FlagReg=pir1
FlagBit=TMR2IF
HandlerCode="if ((pir1 & (1 << TMR2IF)) && (pie1 & (1 << TMR2IE)))\n{\n\tFCM_%n();\n\tclear_bit(pir1, TMR2IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=pie1
EnBit=TMR2IE
OptCnt=3
PrescaleOpt=1
PostScaleOpt=2
RolloverOpt=3
MaxTimerOverflow=256
Opt1="Prescaler Rate"
Opt1Cnt=3
Opt1_1="1:1"
Opt1_1Val="intcon.PEIE=1;\nt2con.T2CKPS0=0;\nt2con.T2CKPS1=0;\nt2con.TMR2ON=1;\n"
Opt1_2="1:4"
Opt1_2Val="intcon.PEIE=1;\nt2con.T2CKPS0=1;\nt2con.T2CKPS1=0;\nt2con.TMR2ON=1;\n"
Opt1_3="1:16"
Opt1_3Val="intcon.PEIE=1;\nt2con.T2CKPS0=0;\nt2con.T2CKPS1=1;\nt2con.TMR2ON=1;\n"
Opt2="Postscaler Rate"
Opt2Cnt=16
Opt2_1="1:1"
Opt2_1Val="t2con = t2con & 0x07;\n"
Opt2_2="1:2"
Opt2_2Val="t2con = (t2con & 0x07) | 0x08;\n"
Opt2_3="1:3"
Opt2_3Val="t2con = (t2con & 0x07) | 0x10;\n"
Opt2_4="1:4"
Opt2_4Val="t2con = (t2con & 0x07) | 0x18;\n"
Opt2_5="1:5"
Opt2_5Val="t2con = (t2con & 0x07) | 0x20;\n"
Opt2_6="1:6"
Opt2_6Val="t2con = (t2con & 0x07) | 0x28;\n"
Opt2_7="1:7"
Opt2_7Val="t2con = (t2con & 0x07) | 0x30;\n"
Opt2_8="1:8"
Opt2_8Val="t2con = (t2con & 0x07) | 0x38;\n"
Opt2_9="1:9"
Opt2_9Val="t2con = (t2con & 0x07) | 0x40;\n"
Opt2_10="1:10"
Opt2_10Val="t2con = (t2con & 0x07) | 0x48;\n"
Opt2_11="1:11"
Opt2_11Val="t2con = (t2con & 0x07) | 0x50;\n"
Opt2_12="1:12"
Opt2_12Val="t2con = (t2con & 0x07) | 0x58;\n"
Opt2_13="1:13"
Opt2_13Val="t2con = (t2con & 0x07) | 0x60;\n"
Opt2_14="1:14"
Opt2_14Val="t2con = (t2con & 0x07) | 0x68;\n"
Opt2_15="1:15"
Opt2_15Val="t2con = (t2con & 0x07) | 0x70;\n"
Opt2_16="1:16"
Opt2_16Val="t2con = (t2con & 0x07) | 0x78;\n"
Opt3="Rollover Value"
Opt3Cnt=5
Opt3_1="256"
Opt3_1Val="pr2=%d-1;\n"
Opt3_2="128"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="64"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="32"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="16"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"