[Device]
Pins=100
Ports=7
ADCPins=32
ADCBits=12
MaxClock=80000000
PrescalerBits=8
ClockDivider=2
ConfigAddress=0xF80000
ConfigCount=8
PortBits=16
PWMCount=8
UARTCount=2
I2CCount=1
SPICount=2
CANCount=1
TimerCount8=0
TimerCount16=9
IntPinCount=5
EepromSize=0
DefaultPackageType=1
FlowcodeProduct=dsPIC33
ChipName=33FJ256GP710A
AltChipName=dsPIC33FJ256GP710A
FlashSize=262144
RamSize=30720
Family=dsPIC33F

[ICD]
ClockPort=2
ClockPin=6
DataPort=2
DataPin=7


[Pins]
Pin1 = "RG15"
Pin2 = "VDD"
Pin3 = "AN29 / RE5"
Pin4 = "AN30 / RE6"
Pin5 = "AN31 / RE7"
Pin6 = "AN16 / RC1"
Pin7 = "AN17 / RC2"
Pin8 = "AN18 / RC3"
Pin9 = "AN19 / RC4"
Pin10 = "SCK2 / RG6"
Pin11 = "SDI2 / RG7"
Pin12 = "SDO2 / RG8"
Pin13 = "MCLR"
Pin14 = "RG9"
Pin15 = "VSS"
Pin16 = "VDD"
Pin17 = "RA0"
Pin18 = "AN20 / INT1 / RA12"
Pin19 = "AN21 / INT2 / RA13"
Pin20 = "AN5 / RB5"
Pin21 = "AN4 / RB4"
Pin22 = "AN3 / RB3"
Pin23 = "AN2 / RB2"
Pin24 = "PGC / AN1 / RB1"
Pin25 = "PGD / AN0 / RB0"
Pin26 = "AN6 / RB6"
Pin27 = "AN7 / RB7"
Pin28 = "RA9"
Pin29 = "VREF+ / RA10"
Pin30 = "AVDD"
Pin31 = "AVSS"
Pin32 = "AN8 / RB8"
Pin33 = "AN9 / RB9"
Pin34 = "AN10 / RB10"
Pin35 = "AN11 / RB11"
Pin36 = "VSS"
Pin37 = "VDD"
Pin38 = "RA1"
Pin39 = "RF13"
Pin40 = "RF12"
Pin41 = "AN12 / RB12"
Pin42 = "AN13 / RB13"
Pin43 = "AN14 / RB14"
Pin44 = "AN15 / RB15"
Pin45 = "VSS"
Pin46 = "VDD"
Pin47 = "RD14"
Pin48 = "RD15"
Pin49 = "RX2 / RF4"
Pin50 = "TX2 / RF5"
Pin51 = "TX1 / RF3"
Pin52 = "RX1 / RF2"
Pin53 = "SDO1 / RF8"
Pin54 = "SDI1 / RF7"
Pin55 = "SCK1 / INT0 / RF6"
Pin56 = "SDA1 / RG3"
Pin57 = "SCL1 / RG2"
Pin58 = "SCL2 / RA2"
Pin59 = "SDA2 / RA3"
Pin60 = "RA4"
Pin61 = "RA5"
Pin62 = "VDD"
Pin63 = "OSC1 / RC12"
Pin64 = "OSC2 / RC15"
Pin65 = "VSS"
Pin66 = "INT3 / RA14"
Pin67 = "INT4 / RA15"
Pin68 = "RD8"
Pin69 = "RD9"
Pin70 = "RD10"
Pin71 = "RD11"
Pin72 = "OC1 / RD0"
Pin73 = "RC13"
Pin74 = "RC14"
Pin75 = "VSS"
Pin76 = "OC2 / RD1"
Pin77 = "OC3 / RD2"
Pin78 = "OC4 / RD3"
Pin79 = "RD12"
Pin80 = "RD13"
Pin81 = "OC5 / RD4"
Pin82 = "OC6 / RD5"
Pin83 = "OC7 / RD6"
Pin84 = "OC8 / RD7"
Pin85 = "VDDcore"
Pin86 = "VDD"
Pin87 = "RF0"
Pin88 = "RF1"
Pin89 = "RG1"
Pin90 = "RG0"
Pin91 = "AN22 / RA6"
Pin92 = "AN23 / RA7"
Pin93 = "AN24 / RE0"
Pin94 = "AN25 / RE1"
Pin95 = "RG14"
Pin96 = "RG12"
Pin97 = "RG13"
Pin98 = "AN26 / RE2"
Pin99 = "AN27 / RE3"
Pin100 = "AN28 / RE4"

[Ports]
PortPin1=0x060F
PortPin3=0x0405
PortPin4=0x0406
PortPin5=0x0407
PortPin6=0x0201
PortPin7=0x0202
PortPin8=0x0203
PortPin9=0x0204
PortPin10=0x0606
PortPin11=0x0607
PortPin12=0x0608
PortPin14=0x0609
PortPin17=0x0000
PortPin18=0x0408
PortPin19=0x0409
PortPin20=0x0105
PortPin21=0x0104
PortPin22=0x0103
PortPin23=0x0102
PortPin24=0x0101
PortPin25=0x0100
PortPin26=0x0106
PortPin27=0x0107
PortPin28=0x0009
PortPin29=0x000A
PortPin32=0x0108
PortPin33=0x0109
PortPin34=0x010A
PortPin35=0x010B
PortPin38=0x0001
PortPin39=0x050D
PortPin40=0x050C
PortPin41=0x010C
PortPin42=0x010D
PortPin43=0x010E
PortPin44=0x010F
PortPin47=0x030E
PortPin48=0x030F
PortPin49=0x0504
PortPin50=0x0505
PortPin51=0x0503
PortPin52=0x0502
PortPin53=0x0508
PortPin54=0x0507
PortPin55=0x0506
PortPin56=0x0603
PortPin57=0x0602
PortPin58=0x0002
PortPin59=0x0003
PortPin60=0x0004
PortPin61=0x0005
PortPin63=0x020C
PortPin64=0x020F
PortPin66=0x000E
PortPin67=0x000F
PortPin68=0x0308
PortPin69=0x0309
PortPin70=0x030A
PortPin71=0x030B
PortPin72=0x0300
PortPin73=0x020D
PortPin74=0x020E
PortPin76=0x0301
PortPin77=0x0302
PortPin78=0x0303
PortPin79=0x030C
PortPin80=0x030D
PortPin81=0x0304
PortPin82=0x0305
PortPin83=0x0306
PortPin84=0x0307
PortPin87=0x0500
PortPin88=0x0501
PortPin89=0x0601
PortPin90=0x0600
PortPin91=0x0006
PortPin92=0x0007
PortPin93=0x0400
PortPin94=0x0401
PortPin95=0x060E
PortPin96=0x060C
PortPin97=0x060D
PortPin98=0x0402
PortPin99=0x0403
PortPin100=0x0404

[PortMasks]
PortMask0=0xC6FF
PortMask1=0xFFFF
PortMask2=0xF01E
PortMask3=0xFFFF
PortMask4=0x03FF
PortMask5=0x31FF
PortMask6=0xF3CF

[ADCPins]
ADC0=25
ADC1=24
ADC2=23
ADC3=22
ADC4=21
ADC5=20
ADC6=26
ADC7=27
ADC8=32
ADC9=33
ADC10=34
ADC11=35
ADC12=41
ADC13=42
ADC14=43
ADC15=44
ADC16=6
ADC17=7
ADC18=8
ADC19=9
ADC20=18
ADC21=19
ADC22=91
ADC23=92
ADC24=93
ADC25=94
ADC26=98
ADC27=99
ADC28=100
ADC29=3
ADC30=4
ADC31=5

[ADC_ConvSpeed]
Count=8
Opt1=FRC
Opt1_Val=64
Opt2=Tcy
Opt2_Val=0
Opt3=Tcy * 2
Opt3_Val=1
Opt4=Tcy * 4
Opt4_Val=3
Opt5=Tcy * 8
Opt5_Val=7
Opt6=Tcy * 16
Opt6_Val=15
Opt7=Tcy * 32
Opt7_Val=31
Opt8=Tcy * 64
Opt8_Val=63

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#define MX_Fosc %c\n\n#include "../support/dsPIC33F/h/p33Fxxxx.h"\n#include <stdlib.h>\n#include <math.h>\n"
MainStart="int main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n\treturn 0;\n}\n\n"
IntStart=""
IntEnd=""
Initialise="AD1PCFGL = 0xffff;\nAD1PCFGH = 0xffff;\n"
IntInit=""
InputCmdFull="TRIS%p = TRIS%p | %m;\n%o = (PORT%p & %m) >> %s;\n"
InputCmdOneBit="TRIS%p = TRIS%p | %m;\n%o = ((PORT%p & %m) == %m);\n"
InputCmdMask="TRIS%p = TRIS%p | %m;\n%o = (PORT%p & %m) >> %s;\n"
OutputCmdFull="TRIS%p = TRIS%p & %i;\nPORT%p = (LAT%p & %i) | %o;\n"
OutputCmdOneBit="TRIS%p = TRIS%p & %i;\nif (%o)\n\tPORT%p = (LAT%p & %i) | %m;\nelse\n\tPORT%p = LAT%p & %i;\n"
OutputCmdMask="TRIS%p = TRIS%p & %i;\nPORT%p = (LAT%p & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
DelayCmdUs="delay_us(%o);\n"
WdtDelayCmdS="Wdt_Delay_S(%o);\n"
WdtDelayCmdMs="Wdt_Delay_Ms(%o);\n"
InitialPortLetter="A"
ConfigData="_%N(%V)  //addr = %a\n"
IntHandler=""

[Defines]
Define1=#define dsPIC33
Define2=#define P33FJ256GP710A
Define3=#define FC_CAL_PIC16BIT
Define4=#define MX_CLKS_PER_INST 2
Define5=#define MX_ADC
Define6=#define MX_ADC_TYPE_8
Define7=#define MX_ADC_BITS_12
Define8=#define MX_SPI_1
Define9=#define MX_SPI_1_MISO_PORT PORTF
Define10=#define MX_SPI_1_MISO_TRIS TRISF
Define11=#define MX_SPI_1_MISO_PIN 2
Define12=#define MX_SPI_1_MOSI_PORT PORTF
Define13=#define MX_SPI_1_MOSI_TRIS TRISF
Define14=#define MX_SPI_1_MOSI_PIN 3
Define15=#define MX_SPI_1_CLK_PORT PORTF
Define16=#define MX_SPI_1_CLK_TRIS TRISF
Define17=#define MX_SPI_1_CLK_PIN 6
Define18=#define MX_SPI_1_SS_PORT PORTF
Define19=#define MX_SPI_1_SS_TRIS TRISF
Define20=#define MX_SPI_2
Define21=#define MX_SPI_2_MISO_PORT PORTG
Define22=#define MX_SPI_2_MISO_TRIS TRISG
Define23=#define MX_SPI_2_MISO_PIN 7
Define24=#define MX_SPI_2_MOSI_PORT PORTG
Define25=#define MX_SPI_2_MOSI_TRIS TRISG
Define26=#define MX_SPI_2_MOSI_PIN 8
Define27=#define MX_SPI_2_CLK_PORT PORTG
Define28=#define MX_SPI_2_CLK_TRIS TRISG
Define29=#define MX_SPI_2_CLK_PIN 6
Define30=#define MX_SPI_2_SS_PORT PORTG
Define31=#define MX_SPI_2_SS_TRIS TRISG
Define32=#define MX_UART_1
Define33=#define MX_UART_1_TX_PORT PORTF
Define34=#define MX_UART_1_TX_TRIS TRISF
Define35=#define MX_UART_1_TX_PIN 3
Define36=#define MX_UART_1_RX_PORT PORTF
Define37=#define MX_UART_1_RX_TRIS TRISF
Define38=#define MX_UART_1_RX_PIN 2
Define39=#define MX_UART_2
Define40=#define MX_UART_2_TX_PORT PORTF
Define41=#define MX_UART_2_TX_TRIS TRISF
Define42=#define MX_UART_2_TX_PIN 5
Define43=#define MX_UART_2_RX_PORT PORTF
Define44=#define MX_UART_2_RX_TRIS TRISF
Define45=#define MX_UART_2_RX_PIN 4
Define46=#define MX_I2C_1
Define47=#define MX_I2C_1_SDA_PORT PORTG
Define48=#define MX_I2C_1_SDA_TRIS TRISG
Define49=#define MX_I2C_1_SDA_PIN  3
Define50=#define MX_I2C_1_SCL_PORT PORTG
Define51=#define MX_I2C_1_SCL_TRIS TRISG
Define52=#define MX_I2C_1_SCL_PIN  2
Define53=#define MX_PWM
Define54=#define MX_PWM_CNT 8
Define55=#define MX_PWM_PSCA1
Define56=#define MX_PWM_PSCA8
Define57=#define MX_PWM_PSCA64
Define58=#define MX_PWM_PSCA256
Define59=#define MX_PWM_1_PORT PORTD
Define60=#define MX_PWM_1_TRIS TRISD
Define61=#define MX_PWM_1_PIN 0
Define62=#define MX_PWM_2_PORT PORTD
Define63=#define MX_PWM_2_TRIS TRISD
Define64=#define MX_PWM_2_PIN 1
Define65=#define MX_PWM_3_PORT PORTD
Define66=#define MX_PWM_3_TRIS TRISD
Define67=#define MX_PWM_3_PIN 2
Define68=#define MX_PWM_4_PORT PORTD
Define69=#define MX_PWM_4_TRIS TRISD
Define70=#define MX_PWM_4_PIN 3
Define71=#define MX_PWM_5_PORT PORTD
Define72=#define MX_PWM_5_TRIS TRISD
Define73=#define MX_PWM_5_PIN 4
Define74=#define MX_PWM_6_PORT PORTD
Define75=#define MX_PWM_6_TRIS TRISD
Define76=#define MX_PWM_6_PIN 5
Define77=#define MX_PWM_7_PORT PORTD
Define78=#define MX_PWM_7_TRIS TRISD
Define79=#define MX_PWM_7_PIN 6
Define80=#define MX_PWM_8_PORT PORTD
Define81=#define MX_PWM_8_TRIS TRISD
Define82=#define MX_PWM_8_PIN 7
Define83=#define MX_ECAN
Define84=#define MX_ECAN2
Define85=#define MX_INT_CNT 5
Define86=#define MX_INT_0_PORT PORTF
Define87=#define MX_INT_0_TRIS TRISF
Define88=#define MX_INT_0_PIN 6
Define89=#define MX_INT_1_PORT PORTA
Define90=#define MX_INT_1_TRIS TRISA
Define91=#define MX_INT_1_PIN 12
Define92=#define MX_INT_2_PORT PORTA
Define93=#define MX_INT_2_TRIS TRISA
Define94=#define MX_INT_2_PIN 13
Define95=#define MX_INT_3_PORT PORTA
Define96=#define MX_INT_3_TRIS TRISA
Define97=#define MX_INT_3_PIN 14
Define98=#define MX_INT_4_PORT PORTA
Define99=#define MX_INT_4_TRIS TRISA
Define100=#define MX_INT_4_PIN 15
Define101=#define MX_IOC_REGS 2
Define102=#define MX_CNEN_MASK1 0xFFFF
Define103=#define MX_CNEN_MASK2 0x00FF

[Interrupts]
GeneralInit=""
Count=17
1=TMR1
2=TMR2
3=TMR3
4=TMR4
5=TMR5
6=TMR6
7=TMR7
8=TMR8
9=TMR9
10=INT0/RF6
11=INT1/RA12
12=INT2/RA13
13=INT3/RA14
14=INT4/RA15
15=PORT
16=RXINT1
17=RXINT2

[TMR1]
Name="TMR1"
HandlerCode="#ifndef MX_ISR_T1\n#define MX_ISR_T1\nvoid _ISR _T1Interrupt(void)\n{\n\tIFS0bits.T1IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC0bits.T1IE = 1;\n"
DisableCode="IEC0bits.T1IE = 0;\n"
OptCnt=3
PrescaleOpt=2
RolloverOpt=3
MaxTimerOverflow=65536
Opt1="Clock Source"
Opt1Cnt=2
Opt1_1="Internal (Fosc/2)"
Opt1_1Val="T1CON = ((T1CON & 0xfffd) | 0x8000);\n"
Opt1_2="External (T1CK)"
Opt1_2Val="T1CON |= 0x8002;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="T1CON &= 0xff0f;\n"
Opt2_2="1:8"
Opt2_2Val="T1CON = ((T1CON & 0xff0f) | 0x0010);\n"
Opt2_3="1:64"
Opt2_3Val="T1CON = ((T1CON & 0xff0f) | 0x0020);\n"
Opt2_4="1:256"
Opt2_4Val="T1CON = ((T1CON & 0xff0f) | 0x0030);\n"
Opt3="Rollover Value"
Opt3Cnt=9
Opt3_1="256"
Opt3_1Val="PR1 = %d-1;\n"
Opt3_2="512"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="1024"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="2048"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="4096"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"
Opt3_6="8192"
Opt3_6Val="NOTE: only Opt3_1Val is needed here"
Opt3_7="16384"
Opt3_7Val="NOTE: only Opt3_1Val is needed here"
Opt3_8="32768"
Opt3_8Val="NOTE: only Opt3_1Val is needed here"
Opt3_9="65536"
Opt3_9Val="NOTE: only Opt3_1Val is needed here"

[TMR2]
Name="TMR2"
HandlerCode="#ifndef MX_ISR_T2\n#define MX_ISR_T2\nvoid _ISR _T2Interrupt(void)\n{\n\tIFS0bits.T2IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC0bits.T2IE = 1;\n"
DisableCode="IEC0bits.T2IE = 0;\n"
OptCnt=3
PrescaleOpt=2
RolloverOpt=3
MaxTimerOverflow=65536
Opt1="Clock Source"
Opt1Cnt=2
Opt1_1="Internal (Fosc/2)"
Opt1_1Val="T2CON = ((T2CON & 0xfffd) | 0x8000);\n"
Opt1_2="External (T2CK)"
Opt1_2Val="T2CON |= 0x8002;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="T2CON &= 0xff0f;\n"
Opt2_2="1:8"
Opt2_2Val="T2CON = ((T2CON & 0xff0f) | 0x0010);\n"
Opt2_3="1:64"
Opt2_3Val="T2CON = ((T2CON & 0xff0f) | 0x0020);\n"
Opt2_4="1:256"
Opt2_4Val="T2CON = ((T2CON & 0xff0f) | 0x0030);\n"
Opt3="Rollover Value"
Opt3Cnt=9
Opt3_1="256"
Opt3_1Val="PR2 = %d-1;\n"
Opt3_2="512"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="1024"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="2048"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="4096"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"
Opt3_6="8192"
Opt3_6Val="NOTE: only Opt3_1Val is needed here"
Opt3_7="16384"
Opt3_7Val="NOTE: only Opt3_1Val is needed here"
Opt3_8="32768"
Opt3_8Val="NOTE: only Opt3_1Val is needed here"
Opt3_9="65536"
Opt3_9Val="NOTE: only Opt3_1Val is needed here"

[TMR3]
Name="TMR3"
HandlerCode="#ifndef MX_ISR_T3\n#define MX_ISR_T3\nvoid _ISR _T3Interrupt(void)\n{\n\tIFS0bits.T3IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC0bits.T3IE = 1;\n"
DisableCode="IEC0bits.T3IE = 0;\n"
OptCnt=3
PrescaleOpt=2
RolloverOpt=3
MaxTimerOverflow=65536
Opt1="Clock Source"
Opt1Cnt=2
Opt1_1="Internal (Fosc/2)"
Opt1_1Val="T3CON = ((T3CON & 0xfffd) | 0x8000);\n"
Opt1_2="External (T3CK)"
Opt1_2Val="T3CON |= 0x8002;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="T3CON &= 0xff0f;\n"
Opt2_2="1:8"
Opt2_2Val="T3CON = ((T3CON & 0xff0f) | 0x0010);\n"
Opt2_3="1:64"
Opt2_3Val="T3CON = ((T3CON & 0xff0f) | 0x0020);\n"
Opt2_4="1:256"
Opt2_4Val="T3CON = ((T3CON & 0xff0f) | 0x0030);\n"
Opt3="Rollover Value"
Opt3Cnt=9
Opt3_1="256"
Opt3_1Val="PR3 = %d-1;\n"
Opt3_2="512"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="1024"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="2048"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="4096"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"
Opt3_6="8192"
Opt3_6Val="NOTE: only Opt3_1Val is needed here"
Opt3_7="16384"
Opt3_7Val="NOTE: only Opt3_1Val is needed here"
Opt3_8="32768"
Opt3_8Val="NOTE: only Opt3_1Val is needed here"
Opt3_9="65536"
Opt3_9Val="NOTE: only Opt3_1Val is needed here"

[TMR4]
Name="TMR4"
HandlerCode="#ifndef MX_ISR_T4\n#define MX_ISR_T4\nvoid _ISR _T4Interrupt(void)\n{\n\tIFS1bits.T4IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC1bits.T4IE = 1;\n"
DisableCode="IEC1bits.T4IE = 0;\n"
OptCnt=3
PrescaleOpt=2
RolloverOpt=3
MaxTimerOverflow=65536
Opt1="Clock Source"
Opt1Cnt=2
Opt1_1="Internal (Fosc/2)"
Opt1_1Val="T4CON = ((T4CON & 0xfffd) | 0x8000);\n"
Opt1_2="External (T4CK)"
Opt1_2Val="T4CON |= 0x8002;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="T4CON &= 0xff0f;\n"
Opt2_2="1:8"
Opt2_2Val="T4CON = ((T4CON & 0xff0f) | 0x0010);\n"
Opt2_3="1:64"
Opt2_3Val="T4CON = ((T4CON & 0xff0f) | 0x0020);\n"
Opt2_4="1:256"
Opt2_4Val="T4CON = ((T4CON & 0xff0f) | 0x0030);\n"
Opt3="Rollover Value"
Opt3Cnt=9
Opt3_1="256"
Opt3_1Val="PR4 = %d-1;\n"
Opt3_2="512"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="1024"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="2048"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="4096"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"
Opt3_6="8192"
Opt3_6Val="NOTE: only Opt3_1Val is needed here"
Opt3_7="16384"
Opt3_7Val="NOTE: only Opt3_1Val is needed here"
Opt3_8="32768"
Opt3_8Val="NOTE: only Opt3_1Val is needed here"
Opt3_9="65536"
Opt3_9Val="NOTE: only Opt3_1Val is needed here"

[TMR5]
Name="TMR5"
HandlerCode="#ifndef MX_ISR_T5\n#define MX_ISR_T5\nvoid _ISR _T5Interrupt(void)\n{\n\tIFS1bits.T5IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC1bits.T5IE = 1;\n"
DisableCode="IEC1bits.T5IE = 0;\n"
OptCnt=3
PrescaleOpt=2
RolloverOpt=3
MaxTimerOverflow=65536
Opt1="Clock Source"
Opt1Cnt=2
Opt1_1="Internal (Fosc/2)"
Opt1_1Val="T5CON = ((T5CON & 0xfffd) | 0x8000);\n"
Opt1_2="External (T5CK)"
Opt1_2Val="T5CON |= 0x8002;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="T5CON &= 0xff0f;\n"
Opt2_2="1:8"
Opt2_2Val="T5CON = ((T5CON & 0xff0f) | 0x0010);\n"
Opt2_3="1:64"
Opt2_3Val="T5CON = ((T5CON & 0xff0f) | 0x0020);\n"
Opt2_4="1:256"
Opt2_4Val="T5CON = ((T5CON & 0xff0f) | 0x0030);\n"
Opt3="Rollover Value"
Opt3Cnt=9
Opt3_1="256"
Opt3_1Val="PR5 = %d-1;\n"
Opt3_2="512"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="1024"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="2048"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="4096"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"
Opt3_6="8192"
Opt3_6Val="NOTE: only Opt3_1Val is needed here"
Opt3_7="16384"
Opt3_7Val="NOTE: only Opt3_1Val is needed here"
Opt3_8="32768"
Opt3_8Val="NOTE: only Opt3_1Val is needed here"
Opt3_9="65536"
Opt3_9Val="NOTE: only Opt3_1Val is needed here"

[TMR6]
Name="TMR6"
HandlerCode="#ifndef MX_ISR_T6\n#define MX_ISR_T6\nvoid _ISR _T6Interrupt(void)\n{\n\tIFS2bits.T6IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC2bits.T6IE = 1;\n"
DisableCode="IEC2bits.T6IE = 0;\n"
OptCnt=3
PrescaleOpt=2
RolloverOpt=3
MaxTimerOverflow=65536
Opt1="Clock Source"
Opt1Cnt=2
Opt1_1="Internal (Fosc/2)"
Opt1_1Val="T6CON = ((T6CON & 0xfffd) | 0x8000);\n"
Opt1_2="External (T6CK)"
Opt1_2Val="T6CON |= 0x8002;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="T6CON &= 0xff0f;\n"
Opt2_2="1:8"
Opt2_2Val="T6CON = ((T6CON & 0xff0f) | 0x0010);\n"
Opt2_3="1:64"
Opt2_3Val="T6CON = ((T6CON & 0xff0f) | 0x0020);\n"
Opt2_4="1:256"
Opt2_4Val="T6CON = ((T6CON & 0xff0f) | 0x0030);\n"
Opt3="Rollover Value"
Opt3Cnt=9
Opt3_1="256"
Opt3_1Val="PR6 = %d-1;\n"
Opt3_2="512"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="1024"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="2048"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="4096"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"
Opt3_6="8192"
Opt3_6Val="NOTE: only Opt3_1Val is needed here"
Opt3_7="16384"
Opt3_7Val="NOTE: only Opt3_1Val is needed here"
Opt3_8="32768"
Opt3_8Val="NOTE: only Opt3_1Val is needed here"
Opt3_9="65536"
Opt3_9Val="NOTE: only Opt3_1Val is needed here"

[TMR7]
Name="TMR7"
HandlerCode="#ifndef MX_ISR_T7\n#define MX_ISR_T7\nvoid _ISR _T7Interrupt(void)\n{\n\tIFS3bits.T7IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC3bits.T7IE = 1;\n"
DisableCode="IEC3bits.T7IE = 0;\n"
OptCnt=3
PrescaleOpt=2
RolloverOpt=3
MaxTimerOverflow=65536
Opt1="Clock Source"
Opt1Cnt=2
Opt1_1="Internal (Fosc/2)"
Opt1_1Val="T7CON = ((T7CON & 0xfffd) | 0x8000);\n"
Opt1_2="External (T7CK)"
Opt1_2Val="T7CON |= 0x8002;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="T7CON &= 0xff0f;\n"
Opt2_2="1:8"
Opt2_2Val="T7CON = ((T7CON & 0xff0f) | 0x0010);\n"
Opt2_3="1:64"
Opt2_3Val="T7CON = ((T7CON & 0xff0f) | 0x0020);\n"
Opt2_4="1:256"
Opt2_4Val="T7CON = ((T7CON & 0xff0f) | 0x0030);\n"
Opt3="Rollover Value"
Opt3Cnt=9
Opt3_1="256"
Opt3_1Val="PR7 = %d-1;\n"
Opt3_2="512"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="1024"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="2048"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="4096"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"
Opt3_6="8192"
Opt3_6Val="NOTE: only Opt3_1Val is needed here"
Opt3_7="16384"
Opt3_7Val="NOTE: only Opt3_1Val is needed here"
Opt3_8="32768"
Opt3_8Val="NOTE: only Opt3_1Val is needed here"
Opt3_9="65536"
Opt3_9Val="NOTE: only Opt3_1Val is needed here"

[TMR8]
Name="TMR8"
HandlerCode="#ifndef MX_ISR_T8\n#define MX_ISR_T8\nvoid _ISR _T1Interrupt(void)\n{\n\tIFS3bits.T8IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC3bits.T8IE = 1;\n"
DisableCode="IEC3bits.T8IE = 0;\n"
OptCnt=3
PrescaleOpt=2
RolloverOpt=3
MaxTimerOverflow=65536
Opt1="Clock Source"
Opt1Cnt=2
Opt1_1="Internal (Fosc/2)"
Opt1_1Val="T8CON = ((T8CON & 0xfffd) | 0x8000);\n"
Opt1_2="External (T8CK)"
Opt1_2Val="T8CON |= 0x8002;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="T8CON &= 0xff0f;\n"
Opt2_2="1:8"
Opt2_2Val="T8CON = ((T8CON & 0xff0f) | 0x0010);\n"
Opt2_3="1:64"
Opt2_3Val="T8CON = ((T8CON & 0xff0f) | 0x0020);\n"
Opt2_4="1:256"
Opt2_4Val="T8CON = ((T8CON & 0xff0f) | 0x0030);\n"
Opt3="Rollover Value"
Opt3Cnt=9
Opt3_1="256"
Opt3_1Val="PR8 = %d-1;\n"
Opt3_2="512"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="1024"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="2048"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="4096"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"
Opt3_6="8192"
Opt3_6Val="NOTE: only Opt3_1Val is needed here"
Opt3_7="16384"
Opt3_7Val="NOTE: only Opt3_1Val is needed here"
Opt3_8="32768"
Opt3_8Val="NOTE: only Opt3_1Val is needed here"
Opt3_9="65536"
Opt3_9Val="NOTE: only Opt3_1Val is needed here"

[TMR9]
Name="TMR9"
HandlerCode="#ifndef MX_ISR_T9\n#define MX_ISR_T9\nvoid _ISR _T1Interrupt(void)\n{\n\tIFS3bits.T9IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC3bits.T9IE = 1;\n"
DisableCode="IEC3bits.T9IE = 0;\n"
OptCnt=3
PrescaleOpt=2
RolloverOpt=3
MaxTimerOverflow=65536
Opt1="Clock Source"
Opt1Cnt=2
Opt1_1="Internal (Fosc/2)"
Opt1_1Val="T9CON = ((T9CON & 0xfffd) | 0x8000);\n"
Opt1_2="External (T9CK)"
Opt1_2Val="T9CON |= 0x8002;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="T9CON &= 0xff0f;\n"
Opt2_2="1:8"
Opt2_2Val="T9CON = ((T9CON & 0xff0f) | 0x0010);\n"
Opt2_3="1:64"
Opt2_3Val="T9CON = ((T9CON & 0xff0f) | 0x0020);\n"
Opt2_4="1:256"
Opt2_4Val="T9CON = ((T9CON & 0xff0f) | 0x0030);\n"
Opt3="Rollover Value"
Opt3Cnt=9
Opt3_1="256"
Opt3_1Val="PR9 = %d-1;\n"
Opt3_2="512"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="1024"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="2048"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="4096"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"
Opt3_6="8192"
Opt3_6Val="NOTE: only Opt3_1Val is needed here"
Opt3_7="16384"
Opt3_7Val="NOTE: only Opt3_1Val is needed here"
Opt3_8="32768"
Opt3_8Val="NOTE: only Opt3_1Val is needed here"
Opt3_9="65536"
Opt3_9Val="NOTE: only Opt3_1Val is needed here"

[INT0/RF6]
Name=INT0/RF6
REMask=0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40
FEMask=0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40
ConfOpt=0x03
EdgeOpt=0x01
HandlerCode="#ifndef MX_ISR_I0\n#define MX_ISR_I0\nvoid _ISR _INT0Interrupt(void)\n{\n\tIFS0bits.INT0IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC0bits.INT0IE = 1;"
DisableCode="IEC0bits.INT0IE = 0;"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of INT0"
Opt1_1Val="INTCON2bits.INT0EP = 0;\n"
Opt1_2="falling edge of INT0"
Opt1_2Val="INTCON2bits.INT0EP = 1;\n"

[INT1/RA12]
Name=INT1/RA12
REMask=0x00,0x10
FEMask=0x00,0x10
ConfOpt=0x03
EdgeOpt=0x01
HandlerCode="#ifndef MX_ISR_I1\n#define MX_ISR_I1\nvoid _ISR _INT1Interrupt(void)\n{\n\tIFS1bits.INT1IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC1bits.INT1IE = 1;"
DisableCode="IEC1bits.INT1IE = 0;"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of INT1"
Opt1_1Val="INTCON2bits.INT1EP = 0;\n"
Opt1_2="falling edge of INT1"
Opt1_2Val="INTCON2bits.INT1EP = 1;\n"

[INT2/RA13]
Name=INT2/RA13
REMask=0x00,0x40
FEMask=0x00,0x40
ConfOpt=0x03
EdgeOpt=0x01
HandlerCode="#ifndef MX_ISR_I2\n#define MX_ISR_I2\nvoid _ISR _INT2Interrupt(void)\n{\n\tIFS1bits.INT2IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC1bits.INT2IE = 1;"
DisableCode="IEC1bits.INT2IE = 0;"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of INT2"
Opt1_1Val="INTCON2bits.INT2EP = 0;\n"
Opt1_2="falling edge of INT2"
Opt1_2Val="INTCON2bits.INT2EP = 1;\n"

[INT3/RA14]
Name=INT3/RA14
REMask=0x00,0x40
FEMask=0x00,0x40
ConfOpt=0x03
EdgeOpt=0x01
HandlerCode="#ifndef MX_ISR_I3\n#define MX_ISR_I3\nvoid _ISR _INT3Interrupt(void)\n{\n\tIFS3bits.INT3IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC3bits.INT3IE = 1;"
DisableCode="IEC3bits.INT3IE = 0;"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of INT3"
Opt1_1Val="INTCON2bits.INT3EP = 0;\n"
Opt1_2="falling edge of INT3"
Opt1_2Val="INTCON2bits.INT3EP = 1;\n"

[INT4/RA15]
Name=INT4/RA15
REMask=0x80
FEMask=0x80
ConfOpt=0x03
EdgeOpt=0x01
HandlerCode="#ifndef MX_ISR_I4\n#define MX_ISR_I4\nvoid _ISR _INT4Interrupt(void)\n{\n\tIFS3bits.INT4IF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC3bits.INT4IE = 1;"
DisableCode="IEC3bits.INT4IE = 0;"
OptCnt=1
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of INT4"
Opt1_1Val="INTCON2bits.INT4EP = 0;\n"
Opt1_2="falling edge of INT4"
Opt1_2Val="INTCON2bits.INT4EP = 1;\n"

[PORT]
Name=PORT
REMask=0xFF,0xFF,0xFF
FEMask=0xFF,0xFF,0xFF
ConfOpt=0x0C
MapReg=1
MapRegCnt=24
MapMask0=C14
MapMask1=C13
MapMask2=B0
MapMask3=B1
MapMask4=B2
MapMask5=B3
MapMask6=B4
MapMask7=B5
MapMask8=G6
MapMask9=G7
MapMask10=G8
MapMask11=G9
MapMask12=B15
MapMask13=D4
MapMask14=D5
MapMask15=D6
MapMask16=D7
MapMask17=F4
MapMask18=F5
MapMask19=D13
MapMask20=D14
MapMask21=D15
MapMask22=A6
MapMask23=A7
HandlerCode="#ifndef MX_ISR_CN\n#define MX_ISR_CN\nvoid _ISR _CNInterrupt(void)\n{\n\tIFS1bits.CNIF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="CNEN1 = %pA*v;\nCNEN2 = %pB*v;\nIEC1bits.CNIE = 1;\n"
DisableCode="IEC1bits.CNIE = 0;\n"
OptCnt=0

[RXINT1]
Name=RXINT1
HandlerCode="#ifndef MX_ISR_RX1\n#define MX_ISR_RX1\nvoid _ISR _U1RXInterrupt(void)\n{\n\tIFS0bits.U1RXIF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC0bits.U1RXIE = 1;\n"
DisableCode="IEC0bits.U1RXIE = 0;\n"
OptCnt=0

[RXINT2]
Name=RXINT2
HandlerCode="#ifndef MX_ISR_RX2\n#define MX_ISR_RX2\nvoid _ISR _U2RXInterrupt(void)\n{\n\tIFS1bits.U2RXIF = 0;\n\tFCM_%n();\n}\n#else\n#warning "This interrupt has previously been enabled, so the macro <%n> may never get called."\n#endif\n"
EnableCode="IEC1bits.U2RXIE = 1;\n"
DisableCode="IEC1bits.U2RXIE = 0;\n"
OptCnt=0