[Device]
Pins=80
Ports=9
ADCPins=12
ADCBits=10
ADCType=12
MaxClock=40000000
PrescalerBits=3
ClockDivider=4
TimerOverflow=256
ConfigAddress=0x300000
ConfigCount=14
PWMCount=2
UARTCount=2
EepromSize=0
HasAltPWM=2
Pwm2IsD4=0
FlowcodeProduct=PIC
DefaultPackageType=1
FlashSize=16384
RamSize=768

[ICD]
ClockPort=1
ClockPin=6
DataPort=1
DataPin=7

[Pins]
Pin1 = "RH2/SEG45"
Pin2 = "RH3/SEG44"
Pin3 = "LCDBIAS2"
Pin4 = "LCDBIAS1"
Pin5 = "RG0/SEG30"
Pin6 = "RG1/TX2/CK2/SEG29"
Pin7 = "RG2/RX2/DT2/SEG28"
Pin8 = "RG3/SEG27"
Pin9 = "RG5/MCLR/VPP"
Pin10 = "RG4/SEG26"
Pin11 = "VSS"
Pin12 = "VDD"
Pin13 = "RF7/SS/SEG25"
Pin14 = "RF6/AN11/SEG24"
Pin15 = "RF5/AN10/CVREF/SEG23"
Pin16 = "RF4/AN9/SEG22"
Pin17 = "RF3/AN8/SEG21"
Pin18 = "RF2/AN7/C1OUT/SEG20"
Pin19 = "RH7/SEG43"
Pin20 = "RH6/SEG42"
Pin21 = "RH5/SEG41"
Pin22 = "RH4/SEG40"
Pin23 = "RF1/AN6/C2OUT/SEG19"
Pin24 = "RF0/AN5/SEG18"
Pin25 = "AVDD"
Pin26 = "AVSS"
Pin27 = "RA3/AN3/VREF+/SEG17"
Pin28 = "RA2/AN2/VREF-/SEG16"
Pin29 = "RA1/AN1"
Pin30 = "RA0/AN0"
Pin31 = "VSS"
Pin32 = "VDD"
Pin33 = "RA5/AN4/HLVDIN/SEG15"
Pin34 = "RA4/T0CKI/SEG14"
Pin35 = "RC1/T1OSI/CCP2"
Pin36 = "RC0/T1OSO/T13CKI"
Pin37 = "RC6/TX1/CK1"
Pin38 = "RC7/RX1/DT1"
Pin39 = "RJ4/SEG39"
Pin40 = "RJ5/SEG38"
Pin41 = "RJ6/SEG37"
Pin42 = "RJ7/SEG36"
Pin43 = "RC2/CCP1/SEG13"
Pin44 = "RC3/SCK/SCL"
Pin45 = "RC4/SDI/SDA"
Pin46 = "RC5/SDO/SEG12"
Pin47 = "RB7/KBI3/PGD"
Pin48 = "VDD"
Pin49 = "OSC1/CLKI/RA7"
Pin50 = "OSC2/CLKO/RA6"
Pin51 = "VSS"
Pin52 = "RB6/KBI2/PGC"
Pin53 = "RB5/KBI1"
Pin54 = "RB4/KBI0/SEG11"
Pin55 = "RB3/INT3/SEG10"
Pin56 = "RB2/INT2/SEG9"
Pin57 = "RB1/INT1/SEG8"
Pin58 = "RB0/INT0"
Pin59 = "RJ3/SEG35"
Pin60 = "RJ2/SEG34"
Pin61 = "RJ1/SEG33"
Pin62 = "RJ0/SEG32"
Pin63 = "RD7/SEG7"
Pin64 = "RD6/SEG6"
Pin65 = "RD5/SEG5"
Pin66 = "RD4/SEG4"
Pin67 = "RD3/SEG3"
Pin68 = "RD2/SEG2"
Pin69 = "RD1/SEG1"
Pin70 = "VSS"
Pin71 = "VDD"
Pin72 = "RD0/SEG0"
Pin73 = "RE7/CCP2/SEG31"
Pin74 = "RE6/COM3"
Pin75 = "RE5/COM2"
Pin76 = "RE4/COM1"
Pin77 = "COM0"
Pin78 = "LCDBIAS3"
Pin79 = "RH0/SEG47"
Pin80 = "RH1/SEG46"

[Ports]
PortPin1=0x0702
PortPin2=0x0703
PortPin5=0x0600
PortPin6=0x0601
PortPin7=0x0602
PortPin8=0x0603
PortPin9=0x0605
PortPin10=0x0604
PortPin13=0x0507
PortPin14=0x0506
PortPin15=0x0505
PortPin16=0x0504
PortPin17=0x0503
PortPin18=0x0502
PortPin19=0x0707
PortPin20=0x0706
PortPin21=0x0705
PortPin22=0x0704
PortPin23=0x0501
PortPin24=0x0500
PortPin27=0x0003
PortPin28=0x0002
PortPin29=0x0001
PortPin30=0x0000
PortPin33=0x0005
PortPin34=0x0004
PortPin35=0x0201
PortPin36=0x0200
PortPin37=0x0206
PortPin38=0x0207
PortPin39=0x0904
PortPin40=0x0905
PortPin41=0x0906
PortPin42=0x0907
PortPin43=0x0202
PortPin44=0x0203
PortPin45=0x0204
PortPin46=0x0205
PortPin47=0x0107
PortPin49=0x0007
PortPin50=0x0006
PortPin52=0x0106
PortPin53=0x0105
PortPin54=0x0104
PortPin55=0x0103
PortPin56=0x0102
PortPin57=0x0101
PortPin58=0x0100
PortPin59=0x0903
PortPin60=0x0902
PortPin61=0x0901
PortPin62=0x0900
PortPin63=0x0307
PortPin64=0x0306
PortPin65=0x0305
PortPin66=0x0304
PortPin67=0x0303
PortPin68=0x0302
PortPin69=0x0301
PortPin72=0x0300
PortPin73=0x0407
PortPin74=0x0406
PortPin75=0x0405
PortPin76=0x0404
PortPin79=0x0700
PortPin80=0x0701

[PortMasks]
PortMask0=0xFF
PortMask1=0xFF
PortMask2=0xFF
PortMask3=0xFF
PortMask4=0xF0
PortMask5=0xFF
PortMask6=0x3F
PortMask7=0xFF
PortMask8=0x00
PortMask9=0xFF

[ADCPins]
ADC0=30
ADC1=29
ADC2=28
ADC3=27
ADC4=33
ADC5=24
ADC6=23
ADC7=18
ADC8=17
ADC9=16
ADC10=15
ADC11=14

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#include <system.h>\n#pragma CLOCK_FREQ %c\n"
MainStart="void main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n}\n\n"
IntStart="void interrupt(void)\n{\n"
IntEnd="}\n\n"
Initialise="adcon1 = 0x0F;\n"
IntInit="\n\n"
InputCmdFull="tris%p = tris%p | %m;\n%o = port%p;\n"
InputCmdOneBit="tris%p = tris%p | %m;\n%o = ((port%p & %m) == %m);\n"
InputCmdMask="tris%p = tris%p | %m;\n%o = port%p & %m;\n"
OutputCmdFull="tris%p = 0x00;\nport%p = %o;\n"
OutputCmdOneBit="tris%p = tris%p & %i;\nif (%o)\n\tport%p = (port%p & %i) | %m;\nelse\n\tport%p = port%p & %i;\n"
OutputCmdMask="tris%p = tris%p & %i;\nport%p = (port%p & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
DelayCmdUs="delay_us(%o);\n"
WdtDelayCmdS="Wdt_Delay_S(%o);\n"
WdtDelayCmdMs="Wdt_Delay_Ms(%o);\n"
InitialPortLetter="a"
ConfigData="#pragma DATA %a, %v\n"
IntHandler="if (%r & (1 << %b))\n{\n\tFCM_%n();\n\tclear_bit(%r, %b);\n}\n"

[Defines]
Define1=#define P18F8490
Define2=#define MX_SPI
Define3=#define MX_SPI_C
Define4=#define MX_SPI_SDI 4
Define5=#define MX_SPI_SDO 5
Define6=#define MX_SPI_SCK 3
Define7=#define MX_UART
Define8=#define MX_UART_C
Define9=#define MX_UART_TX 6
Define10=#define MX_UART_RX 7
Define11=#define MX_I2C
Define12=#define MX_MI2C
Define13=#define MX_I2C_C
Define14=#define MX_I2C_SDA 4
Define15=#define MX_I2C_SCL 3
Define16=#define MX_PWM
Define17=#define MX_PWM_CNT 2
Define18=#define MX_PWM_TRIS1 trisc
Define19=#define MX_PWM_1 2
Define20=#define MX_PWM_TRIS2 trisc
Define21=#define MX_PWM_2 1
Define22=#define MX_PWM_TRIS2a trise
Define23=#define MX_PWM_2a 7

[Interrupts]
;first 3 should always be 1=TMR0, 2=RB0INT, 3=PORTB
;any other interrupts need to also have this set: "intcon.PEIE=1;\n"
GeneralInit="intcon.GIE=1;\n"
Count=9
1=TMR0
2=RB0INT
3=PORTB
4=TMR1
5=RB1INT
6=RB2INT
7=RB3INT
8=RXINT
9=TMR2

[TMR0]
Name="TMR0"
FlagReg=intcon
FlagBit=TMR0IF
HandlerCode="if ((intcon & (1 << TMR0IF)) && (intcon & (1 << TMR0IE)))\n{\n\tFCM_%n();\n\tclear_bit(intcon, TMR0IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=intcon
EnBit=TMR0IE
OptCnt=3
PrescaleOpt=3
MaxTimerOverflow=256
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T0CKI pin"
Opt1_1Val="t0con.T0CS=1;\n"
Opt1_2="Internal clock (CLKO)"
Opt1_2Val="t0con.T0CS=0;\n"
Opt2="Source Edge Select"
Opt2Cnt=2
Opt2_1="high-to-low transition on T0CKI"
Opt2_1Val="t0con.T0SE=1;\n"
Opt2_2="low-to-high transition on T0CKI"
Opt2_2Val="t0con.T0SE=0;\n"
Opt3="Prescaler Rate"
Opt3Cnt=9
Opt3_1="1:1"
Opt3_1Val="t0con = (t0con & 0xF0) | 0x08;\n"
Opt3_2="1:2"
Opt3_2Val="t0con = (t0con & 0xF0) | 0x00;\n"
Opt3_3="1:4"
Opt3_3Val="t0con = (t0con & 0xF0) | 0x01;\n"
Opt3_4="1:8"
Opt3_4Val="t0con = (t0con & 0xF0) | 0x02;\n"
Opt3_5="1:16"
Opt3_5Val="t0con = (t0con & 0xF0) | 0x03;\n"
Opt3_6="1:32"
Opt3_6Val="t0con = (t0con & 0xF0) | 0x04;\n"
Opt3_7="1:64"
Opt3_7Val="t0con = (t0con & 0xF0) | 0x05;\n"
Opt3_8="1:128"
Opt3_8Val="t0con = (t0con & 0xF0) | 0x06;\n"
Opt3_9="1:256"
Opt3_9Val="t0con = (t0con & 0xF0) | 0x07;\n"

[RB0INT]
Name="RB0/INT0"
FlagReg=intcon
FlagBit=INT0IF
HandlerCode="if ((intcon & (1 << INT0IF)) && (intcon & (1 << INT0IE)))\n{\n\tFCM_%n();\n\tclear_bit(intcon, INT0IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=intcon
EnBit=INT0IE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB0/INT0"
Opt1_1Val="intcon2.INTEDG0=1;\n"
Opt1_2="falling edge of RB0/INT0"
Opt1_2Val="intcon2.INTEDG0=0;\n"

[PORTB]
Name="PORT"
FlagReg=intcon
FlagBit=RBIF
HandlerCode="char mxtmp;\nif ((intcon & (1 << RBIF)) && (intcon & (1 << RBIE)))\n{\n\tFCM_%n();\n\tmxtmp=portb;\n\tclear_bit(intcon, RBIF);\n}\n"
UseExplicitHandlerCode=1
EnReg=intcon
EnBit=RBIE
OptCnt=0
TmrOpt=0

[TMR1]
Name="TMR1"
FlagReg=pir1
FlagBit=TMR1IF
HandlerCode="if ((pir1 & (1 << TMR1IF)) && (pie1 & (1 << TMR1IE)))\n{\n\tFCM_%n();\n\tclear_bit(pir1, TMR1IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=pie1
EnBit=TMR1IE
OptCnt=2
PrescaleOpt=2
MaxTimerOverflow=65536
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T1CKI pin"
Opt1_1Val="intcon.PEIE=1;\nt1con.T1OSCEN=1;\nt1con.TMR1ON=1;\nt1con.TMR1CS=1;\n"
Opt1_2="Internal clock (Fosc/4)"
Opt1_2Val="intcon.PEIE=1;\nt1con.T1OSCEN=1;\nt1con.TMR1ON=1;\nt1con.TMR1CS=0;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="t1con = t1con & 0x0F;\n"
Opt2_2="1:2"
Opt2_2Val="t1con = (t1con & 0x0F) | 0x10;\n"
Opt2_3="1:4"
Opt2_3Val="t1con = (t1con & 0x0F) | 0x20;\n"
Opt2_4="1:8"
Opt2_4Val="t1con = (t1con & 0x0F) | 0x30;\n"

[RB1INT]
Name="RB1/INT1"
FlagReg=intcon3
FlagBit=INT1IF
HandlerCode="if ((intcon3 & (1 << INT1IF)) && (intcon3 & (1 << INT1IE)))\n{\n\tFCM_%n();\n\tclear_bit(intcon3, INT1IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=intcon3
EnBit=INT1IE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB1/INT1"
Opt1_1Val="intcon2.INTEDG1=1;\n"
Opt1_2="falling edge of RB1/INT1"
Opt1_2Val="intcon2.INTEDG1=0;\n"

[RB2INT]
Name="RB2/INT2"
FlagReg=intcon3
FlagBit=INT2IF
HandlerCode="if ((intcon3 & (1 << INT2IF)) && (intcon3 & (1 << INT2IE)))\n{\n\tFCM_%n();\n\tclear_bit(intcon3, INT2IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=intcon3
EnBit=INT2IE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB2/INT2"
Opt1_1Val="intcon2.INTEDG2=1;\n"
Opt1_2="falling edge of RB2/INT2"
Opt1_2Val="intcon2.INTEDG2=0;\n"

[RB3INT]
Name="RB3/INT3"
FlagReg=intcon3
FlagBit=INT3IF
HandlerCode="if ((intcon3 & (1 << INT3IF)) && (intcon3 & (1 << INT3IE)))\n{\n\tFCM_%n();\n\tclear_bit(intcon3, INT3IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=intcon3
EnBit=INT3IE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB3/INT3"
Opt1_1Val="intcon2.INTEDG3=1;\n"
Opt1_2="falling edge of RB3/INT3"
Opt1_2Val="intcon2.INTEDG3=0;\n"

[RXINT]
Name="RXINT"
FlagReg=pir1
FlagBit=RCIF
HandlerCode="if ((pir1 & (1 << RCIF)) && (pie1 & (1 << RCIE)))\n{\n\tFCM_%n();\n\tclear_bit(pir1, RCIF);\n}\n"
UseExplicitHandlerCode=1
EnReg=pie1
EnBit=RCIE
OptCnt=0
TmrOpt=0

[TMR2]
Name="TMR2"
FlagReg=pir1
FlagBit=TMR2IF
HandlerCode="if ((pir1 & (1 << TMR2IF)) && (pie1 & (1 << TMR2IE)))\n{\n\tFCM_%n();\n\tclear_bit(pir1, TMR2IF);\n}\n"
UseExplicitHandlerCode=1
EnReg=pie1
EnBit=TMR2IE
OptCnt=3
PrescaleOpt=1
PostScaleOpt=2
RolloverOpt=3
MaxTimerOverflow=256
Opt1="Prescaler Rate"
Opt1Cnt=3
Opt1_1="1:1"
Opt1_1Val="intcon.PEIE=1;\nt2con.T2CKPS0=0;\nt2con.T2CKPS1=0;\nt2con.TMR2ON=1;\n"
Opt1_2="1:4"
Opt1_2Val="intcon.PEIE=1;\nt2con.T2CKPS0=1;\nt2con.T2CKPS1=0;\nt2con.TMR2ON=1;\n"
Opt1_3="1:16"
Opt1_3Val="intcon.PEIE=1;\nt2con.T2CKPS0=0;\nt2con.T2CKPS1=1;\nt2con.TMR2ON=1;\n"
Opt2="Postscaler Rate"
Opt2Cnt=16
Opt2_1="1:1"
Opt2_1Val="t2con = t2con & 0x07;\n"
Opt2_2="1:2"
Opt2_2Val="t2con = (t2con & 0x07) | 0x08;\n"
Opt2_3="1:3"
Opt2_3Val="t2con = (t2con & 0x07) | 0x10;\n"
Opt2_4="1:4"
Opt2_4Val="t2con = (t2con & 0x07) | 0x18;\n"
Opt2_5="1:5"
Opt2_5Val="t2con = (t2con & 0x07) | 0x20;\n"
Opt2_6="1:6"
Opt2_6Val="t2con = (t2con & 0x07) | 0x28;\n"
Opt2_7="1:7"
Opt2_7Val="t2con = (t2con & 0x07) | 0x30;\n"
Opt2_8="1:8"
Opt2_8Val="t2con = (t2con & 0x07) | 0x38;\n"
Opt2_9="1:9"
Opt2_9Val="t2con = (t2con & 0x07) | 0x40;\n"
Opt2_10="1:10"
Opt2_10Val="t2con = (t2con & 0x07) | 0x48;\n"
Opt2_11="1:11"
Opt2_11Val="t2con = (t2con & 0x07) | 0x50;\n"
Opt2_12="1:12"
Opt2_12Val="t2con = (t2con & 0x07) | 0x58;\n"
Opt2_13="1:13"
Opt2_13Val="t2con = (t2con & 0x07) | 0x60;\n"
Opt2_14="1:14"
Opt2_14Val="t2con = (t2con & 0x07) | 0x68;\n"
Opt2_15="1:15"
Opt2_15Val="t2con = (t2con & 0x07) | 0x70;\n"
Opt2_16="1:16"
Opt2_16Val="t2con = (t2con & 0x07) | 0x78;\n"
Opt3="Rollover Value"
Opt3Cnt=5
Opt3_1="256"
Opt3_1Val="pr2=%d-1;\n"
Opt3_2="128"
Opt3_2Val="NOTE: only Opt3_1Val is needed here"
Opt3_3="64"
Opt3_3Val="NOTE: only Opt3_1Val is needed here"
Opt3_4="32"
Opt3_4Val="NOTE: only Opt3_1Val is needed here"
Opt3_5="16"
Opt3_5Val="NOTE: only Opt3_1Val is needed here"