Hi David
I did open the asm file in mplab and program the chip and it did say that it programmed the chip sucessfullly but the hardware did nothing like it was still blank. So im not sure if that is what you mean.
Cheers
Christian
Search found 8 matches
- Thu Jul 05, 2012 12:58 am
- Forum: Flowcode V4
- Topic: Failed to program 12f675
- Replies: 3
- Views: 4029
- Wed Jul 04, 2012 1:37 am
- Forum: Flowcode V4
- Topic: Failed to program 12f675
- Replies: 3
- Views: 4029
Failed to program 12f675
Hi all
I tried to program my 12f675 and it fails to program the chip it appears to erase the device sucessfully. I have copied the programing report below. Any help would be greatly apreciated.
Regards
Christian O'Callaghan
success
Return code = 0
Launching the linker/assembler...
e:\program ...
I tried to program my 12f675 and it fails to program the chip it appears to erase the device sucessfully. I have copied the programing report below. Any help would be greatly apreciated.
Regards
Christian O'Callaghan
success
Return code = 0
Launching the linker/assembler...
e:\program ...
- Wed Jun 20, 2012 9:05 am
- Forum: Flowcode V4
- Topic: pic12F1840 incomplete fcd and wake from sleep problem
- Replies: 2
- Views: 3489
Re: pic12F1840 incomplete fcd and wake from sleep problem
Hi Ben
Thanks for the help. Your solution compiled fine but would not work on hardware. Going through the C and asm file showed no issues all addresses were correct and the op-codes were right just would not function didn't matter what pin was pulled low would not interrupt. I have made a ...
Thanks for the help. Your solution compiled fine but would not work on hardware. Going through the C and asm file showed no issues all addresses were correct and the op-codes were right just would not function didn't matter what pin was pulled low would not interrupt. I have made a ...
- Tue Jun 19, 2012 1:33 pm
- Forum: Flowcode V4
- Topic: pic12F1840 incomplete fcd and wake from sleep problem
- Replies: 2
- Views: 3489
pic12F1840 incomplete fcd and wake from sleep problem
Hi All
No longer a NOOB but no flowcode guru either. I have been having alot of problems with the timer0 interrupt properties. Also the portB interrupt icon has not got any properties available. I have downloaded a new fcd file from another post about timer1 on this chip which helped tmr1 but not ...
No longer a NOOB but no flowcode guru either. I have been having alot of problems with the timer0 interrupt properties. Also the portB interrupt icon has not got any properties available. I have downloaded a new fcd file from another post about timer1 on this chip which helped tmr1 but not ...
- Fri Feb 04, 2011 2:25 am
- Forum: Flowcode V4
- Topic: Pickit 3 Initialize failed!
- Replies: 7
- Views: 5551
Re: Pickit 3 Initialize failed!
Hi Ben
I thought I would post in with some good news IT's ALIVE. It appears that the mplab v8.30 was causing conflicts. So on the fresh OS install I downloaded and installed the latest version of mplab V8.63 and now it is working a treat I even have a flashing LED on my test circuit. I am ...
I thought I would post in with some good news IT's ALIVE. It appears that the mplab v8.30 was causing conflicts. So on the fresh OS install I downloaded and installed the latest version of mplab V8.63 and now it is working a treat I even have a flashing LED on my test circuit. I am ...
- Fri Feb 04, 2011 1:15 am
- Forum: Flowcode V4
- Topic: Pickit 3 Initialize failed!
- Replies: 7
- Views: 5551
Re: Pickit 3 Initialize failed!
Hi Ben
After having no luck to to resolve the Initialize failed! error. I decide to do a clean install of windows 7 x86 on a separate partition on the pc (hp laptop) to eliminate any software/driver conflicts. These are my observations so far.
Once everything was installed minus mplab I would get ...
After having no luck to to resolve the Initialize failed! error. I decide to do a clean install of windows 7 x86 on a separate partition on the pc (hp laptop) to eliminate any software/driver conflicts. These are my observations so far.
Once everything was installed minus mplab I would get ...
- Wed Feb 02, 2011 10:51 pm
- Forum: Flowcode V4
- Topic: Pickit 3 Initialize failed!
- Replies: 7
- Views: 5551
Re: Pickit 3 Initialize failed!
Hi Ben
I am using the latest release, I believe it is V4.3.7.63 I tried to update it once it was installed but it said it was the latest version.
Would it have anything to do with the fact that the drive letter on that os is not C:\ but E:\ I do remember reading a post about
non standard ...
I am using the latest release, I believe it is V4.3.7.63 I tried to update it once it was installed but it said it was the latest version.
Would it have anything to do with the fact that the drive letter on that os is not C:\ but E:\ I do remember reading a post about
non standard ...
- Wed Feb 02, 2011 9:03 am
- Forum: Flowcode V4
- Topic: Pickit 3 Initialize failed!
- Replies: 7
- Views: 5551
Pickit 3 Initialize failed!
Hi all
I have made a very simple led flasher program and it simulates perfectly. Flowcode also compiles to c ok aswell but when I try to compile to the pic mcu I get the following error.
I am using the pic16f1827 on a proto board and the Hi Tech compiler Lite. I have been through all settings a ...
I have made a very simple led flasher program and it simulates perfectly. Flowcode also compiles to c ok aswell but when I try to compile to the pic mcu I get the following error.
I am using the pic16f1827 on a proto board and the Hi Tech compiler Lite. I have been through all settings a ...