Matrix user forums

I am trying to use this byte line in FC's C-Code box byte id155_init[8] = { 0xFF, 0x97, 0xD0, 0x94, 0x00, 0x08, 0x00, 0x6F }; I create an id155_init variable and write the line like this in the C-Code box: FCV_id155_init[8] = { 0xFF, 0x97, 0xD0, 0x94, 0x00, 0x08, 0x00, 0x6F }; I get this error when ...

Here is the arduino program that I want converted

Hi, I have an Arduino program that I need to convert to Flowcode, but my knowledge of the Arduino platform is not good enough for this. Is there anyone out there who wants to take this job. I would be happy to pay you for this :-) Please send me a PM or an email to kennethnilsen69@gmail.com if you a...

Your solution is not what Ben describes. An I/O pin is connected VUSB and has a pull down. Not VUSB is connected to GND with a resistor. The question is of course which I/O pin... thank you very much for that kersing :-) it worked when I found the right input port :-)))) Now it boots up properly :-...

I added a 10k resistor between VUSB and GND but unfortunately it did not help. it still goes straight into the bootloader and stays there for 1 minute and 50 seconds before booting into using the program.

any more ideas on why?

I use the same bootloader as you have on ECIO

Hmm it seems to always enter bootloader even without USB connected. and stays there for about 1 minute and 50 seconds then it goes out of Bootloader and boots up normally. are these any settings I am missing in MPLAB IPE? or there may be a fault in the pcb card.

bootloader into the auxillary flash did the trick. now usb and 140MHz work and i can program it like a regular ECIO40P16 Thank you so much Ben

like this?

Hi Ben can I do this in flowcode with the C Code icon and then upload it to the chip with the PICkit4 device?

Is this just a one-time thing to do? it will stay that way after I upload the regular hex program

I have make my own pcb with the same chip as in ECIO40P16 and there are a few things I do not understand ECIO40P16 has an external crystal at 8MHz but runs at 140MHz. how is this possible? Mine only works properly if I choose 8MHz but as you know, it is much slower than 140MHz. so what is it I have ...

The problem is only on these pop ups Properties menus so I can live with it for a while longer :-). if there is any I need to read then I just change the Windows text size and back again after. but mostly I know what is written there even though I can not see the text :-) just a little annoying mome...

After a lot of testing with various screen resolutions and text size, I have come to the conclusion that an FC does not support 3840 x 1080 with 100% text size. if I increase the text to 150% then it will be ok but then everything else will be too big so that way I can not have it. Do you have time ...

I suspect it has something to do with my screen resolution. I use a 49" gaming display with a resolution of 3840 x 1080. Is FC compatible with this resolution?

when I disconnect that screen I can read all the text on the other screen. but must disconnect for it to work

Hi I have got a problem with the text size in FC7 that I can not figure out. anyone know how to fix this?
The problem is only in FC7 so I do not think it is a windows problem.

the latest update fixed the problem with Nano but not on the EPIO40P16

for the Arduino Nano I can't use any Timer components. just by adding a Timer component on a blank project to Nano I get this error message: Launching the compiler... C:\Program Files (x86)\Flowcode 7\compilers\avr\batchfiles\avra.bat atmega328p "C:\Users\Kenneth\DOCUME~1\Arduino\TimerTestNano....

Hi I have problems if I want to use more than 4 Timer components. I can not make the 5 Timer to work. In the Timer component, up to 9 Timers are available

Are there any restrictions or is this a bug?

I use:
FC7 and a EPIO40P16

Sorry Benj but no difference with the latest update

And if I swap around Internal 1 and 2 i get this (only software swap)

Hello, I believe I may have now fixed the problem. In the initialisation of the DMA the channel 2 pointers were referring to the channel 1 pins. Hopefully should all be resolved for you now. Please copy the attached file into your "Flowcode 7/CAL/PIC16BIT" folder and let us know how you g...

Hello, Please can you confirm you are using FLowcode v7.3 and have applied the fixes from here. https://www.matrixtsl.com/mmforums/viewtopic.php?f=63&t=19743#p86234 There are some CAN related fixes in there. I'm just combing through the internal CAL code now to see if I can spot any problems. Y...

There is also another problem:
If I initialise CAN2, SetTxIdent and SetTxData do not work on CAN1

I have now moved it to D5 and D4 and here everything works


Thanks for the help

Now I have moved them over to 3.3 volts and I now measure 3.2 volts on B7 and B6.

But it does not help on the problem It still does not work.

I have also tested the ports with LED diodes and they work as they should and are not damaged by 3.7v for just a few seconds

Even with pull-ups to 5V so there is only 3.7 volts on pin B7 and B6 so I do not think has been damaged by it.

I move them over to the 3.3v output but have my doubts that this is the reason why it does not work