Hello Benj,
Yes, I have tried it, but it do not working.
I have also to read to the value of the push button with lcd . The value was "32".
Regards
Flurk
Search found 9 matches
- Mon May 19, 2008 9:11 pm
- Forum: Formula Flowcode
- Topic: problem buggy-flowcode
- Replies: 2
- Views: 6135
- Sun May 18, 2008 9:46 pm
- Forum: Formula Flowcode
- Topic: problem buggy-flowcode
- Replies: 2
- Views: 6135
problem buggy-flowcode
Hello everyone, The flowcode which you see in the appendix work perfectly. The motor works as wished. code004.jpg But when I component adds "formula flowcode" it wants no longer work. (see attachment 2) Only by adding component it. Therefore changes nothing in the flowcode. code005.jpg Can...
- Wed May 14, 2008 10:14 pm
- Forum: E-blocks
- Topic: internet board
- Replies: 3
- Views: 4166
Re: internet board
Hello Steve,
For to start I want upgrade firstly my student version.
How much go does me that costs?
Regards
Flurk
For to start I want upgrade firstly my student version.
How much go does me that costs?
Regards
Flurk
- Thu May 01, 2008 10:17 pm
- Forum: E-blocks
- Topic: internet board
- Replies: 3
- Views: 4166
internet board
Hello,
I has bought a Internet module .
It is not possible to compile , perhaps because I have a students version. (flowcode V3)
What must I do to for, however, is possible.
Regards
Flurk
I has bought a Internet module .
It is not possible to compile , perhaps because I have a students version. (flowcode V3)
What must I do to for, however, is possible.
Regards
Flurk
- Thu Jan 10, 2008 10:41 pm
- Forum: Formula Flowcode
- Topic: problem buggy
- Replies: 9
- Views: 11508
Hello Ok our switches are normally fairly reliable but occasionally they can be a little awkward. Try sliding the switch off and on with a solid but not forceful motion. Make sure you are moving the switch as far as it will go in either direction. This normally acts to sort out the switch and impro...
- Wed Jan 09, 2008 10:53 pm
- Forum: Formula Flowcode
- Topic: problem buggy
- Replies: 9
- Views: 11508
Hello Flurk If you switch on the Buggy, Plug it into the USB and then press the reset button on top of the Buggy do any of the LEDs at the front of the Buggy light up? Also can you verify that the 5V you are testing from the batteries is coming though to the PCB. Eg are the VSS and VDD pins of the ...
- Tue Jan 08, 2008 11:14 pm
- Forum: Formula Flowcode
- Topic: problem buggy
- Replies: 9
- Views: 11508
Hello Flurk, When you plug in the USB cable, in the buggy and in the PC, and you switch on the Buggy, led 7 and 6 should start blinking. If this does not happen, you probably have a bad battery connection. How you can solve this is described nicely (with photographs) in the getting started guide on...
- Tue Jan 08, 2008 10:24 pm
- Forum: Formula Flowcode
- Topic: problem buggy
- Replies: 9
- Views: 11508
- Mon Jan 07, 2008 11:15 pm
- Forum: Formula Flowcode
- Topic: problem buggy
- Replies: 9
- Views: 11508
problem buggy
Hello, I have my first programme download to the flowcode robot. Everything went good, but it didn't works. (i now, i have used de wrong gate) After downloading is the problem, I can't make connection to the PC. Also when it have pressed on SW1 But the led's RD7 and RD6 do not blink ! USB-led is on....