Matrix user forums

Posted: **Sun May 21, 2017 7:11 pm**

User Type Device: MAC (Arduino) MI5466
Used for motor control for LawnMower.

The code below works:

PulseTiming-Mega2560-I2C.fcfx: (16.85 KiB) Downloaded 426 times

But try convert to MIAC (Arduino) MI5466 but do not work.
See below:

MIAC-LawnMower.fcfx: (18.07 KiB) Downloaded 434 times

Is there anyone here that can see where things are going wrong.
Hope someone here will help solve the problem.

Posted: **Sun May 21, 2017 7:53 pm**

would love to see that when it's finished

Steve

Posted: **Mon May 22, 2017 10:12 am**

Can PulsTiming work in MAC (Arduino) MI5466 Like MEGA 2560 ?
And what should be changed in the coder so that PulsTiming can work with MAC ?

Posted: **Mon May 22, 2017 10:57 am**

Hi Monie,

In the "while sw = 1" loops you need to change the InputANALOG() into InputDIGITAL()
Or change the compare value to your own threshold, e.g. while sw > 128
The value will depend on what range of voltage you have into the MIAC inputs.

Posted: **Mon May 22, 2017 11:58 am**

Thank you very much LeighM.
Have worked a lot about the problem;)
Please see attached File:

MIAC-LawnMower-001.fcfx: (19.28 KiB) Downloaded 433 times

Voltage range I have input MIAC inputs.
0.878 Vdc to 1.003 Vdc

Posted: **Mon May 22, 2017 12:58 pm**

Hi Monie,
If your MIAC input high voltage is between 0.878 Vdc to 1.003 Vdc then it will not be high enough to trigger a logic high.
Have a look at the conversion chart on page 18 of the MIAC datasheet.
In this case you will need to use the InputANALOG() which will return a value of about 20 for an input of 1 Volt.
So if your input voltage is 0v for off and about 1v for on, then I suggest you test for values above and below a threshold of about 10...

: MIAC_Analog_Input.jpg (14.17 KiB) Viewed 20804 times

Posted: **Mon May 22, 2017 1:39 pm**

Hi LeighM,
Have tried your suggestion but enter resultal, only "0" is displayed.
So right now I do not know what to do!
What do you say to convert ouput up?
Can this be used or is something I can not
Else how much should I convert?

Posted: **Mon May 22, 2017 1:46 pm**

What is the circuit that supplies voltage into the MIAC input?
The MIAC has an input resistance of 10K

Posted: **Mon May 22, 2017 4:29 pm**

Hi LeighM

Is it the device below which supplies voltage to MIAC input?
Remote control system
Receiver type FS-R9B

: FS-R9B.jpg (25.59 KiB) Viewed 20797 times

manual for FS-R9B
https://www.aliexpress.com/store/produc ... 55869.html

Posted: **Mon May 22, 2017 5:19 pm**

Ah, I see, I missed the fact that you are using an RC servo system.
You would need to use MIAC Inputs 1 and 2 as direct digital inputs with InputDIGITAL(),
only these two inputs connect directly to digital inputs on the processor.
The InputANALOG() will be too slow.
The next problem is that the RC receiver channel outputs will not be a high enough voltage,
so you will need to level shift from the RC logic level to the MIAC level,
something like this should do it ...
https://www.onsemi.com/pub/Collateral/MC14504B-D.PDF

Posted: **Mon May 22, 2017 6:43 pm**

Hi LeighM

Thank you very much for your help.
I want to work on my project

Posted: **Tue May 23, 2017 7:53 am**

Hi LeighM
Trying to use dsPIC .Type MI5809
But now the interrupt not will work!
See attached code:

MIACdsPIC-LawnMower.fcfx: (19.33 KiB) Downloaded 375 times

Do you have a suggestion?

Posted: **Tue May 23, 2017 8:43 am**

Hi,
I have made some changes in CH2 macro, you still had a test for sw < 20 for the digital return.
Hope that helps.
Leigh

Posted: **Tue May 23, 2017 9:19 am**

Hi LeighM
Received notification when trying to upload at Interrupt error
See compiler messages below!

Code: Select all

Target folder: C:\Users\Bruger\Desktop\MIACTI~1
Source name:   C:\Users\Bruger\Desktop\MIAC til FLOWCODE FORUM\MIACdsPIC-LawnMower.fcfx
Title:         
Description:   
Device:        PIC16.33E.MIAC (dsPIC)
Generated by:  Flowcode v7.2.1.4
Date:          Tuesday, May 23, 2017 10:01:10
Users:         1
Registered to: monie jacobsen
Licence key:   YUWNEC
http://www.flowcode.co.uk
Launching the compiler...
C:\Program Files (x86)\Flowcode 7\compilers\pic16\batchfiles\pic16_C30_comp.bat  "MIACdsPIC-LawnMower" "C:\Users\Bruger\Desktop\MIACTI~1\" "33EP256MU806"
Launching compiler...

C:\Users\Bruger\Desktop\MIACTI~1>xc16-gcc -c -mcpu="33EP256MU806" -omf=coff -funsigned-char -fno-short-double -Os -I"C:\PROGRA~2\FLOWCO~1\COMPIL~1\pic16\BATCHF~1\..\support\h" -I"C:\PROGRA~2\FLOWCO~1\COMPIL~1\pic16\BATCHF~1\" -std=gnu99 "MIACdsPIC-LawnMower".c -o "MIACdsPIC-LawnMower".o 
Options have been disabled due to restricted license
Visit http://www.microchip.com/ to purchase a new key.
MIACdsPIC-LawnMower.c: In function 'FCM_CH2':
MIACdsPIC-LawnMower.c:1392:2: error: 'TCNT0' undeclared (first use in this function)
MIACdsPIC-LawnMower.c:1392:2: note: each undeclared identifier is reported only once for each function it appears in

Error returned from [xc16-gcc.exe]
Completed compilation, return = 1

C:\Program Files (x86)\Flowcode 7\compilers\pic16\batchfiles\pic16_C30_comp.bat reported error code 1



FINISHED

Posted: **Tue May 23, 2017 9:31 am**

Hi,
You can remove your Reset timer C icon, it should be TMR1 and this is reset in the Interrupt Enable ...

Code: Select all

// TCNT0 = 0;

And the last one after the Interrupt Disable should be ...

Code: Select all

FCV_TSUM = TMR1;

Posted: **Tue May 23, 2017 10:55 am**

Hi Leigh
Thank you for your great help.
Now I can upload code to dsPIC.
I try to convert Receiver type FS-R9B output signal up.

Posted: **Tue May 30, 2017 12:07 pm**

Hi LeighM
I have now got the RC logic level to the MIAC.
The converted RC outputs 4V to 12V according to the oscilloscope.

: 5v-to-12v-logic-level-shifter.gif (3.99 KiB) Viewed 20612 times

But in dsPIC. Type MI5809 does not show the correct ouput for display that should be 0- 255 bit
User RC-Servo Test:

: RC-Servo-Test.JPG (18.99 KiB) Viewed 20614 times

Result shown in display from dsPIC .Type MI5809.
See ouput below:

MIACdsPIC-LawnMower-003.fcfx: (18.78 KiB) Downloaded 355 times

By from RC servo is 800 til 2200 Pulse
Has attached the FlowCodes below:
Servo: Output display:
800 - 255 bit
935 - 0 bit
1147 - 30 bit
1351 - 194 bit
1827 - 255 bit
1930 - 0 bit

But want Output for display from 0 to 255 bit

Can you see the codes where it goes wrong:
I would be very happy for your help

Posted: **Tue May 30, 2017 3:08 pm**

Perhaps you could display the tsum value before (and after) the Map, also use an (additional) different variable for the output of Map.
Then you will be able to see the raw timer values that the MIAC uses, and then adjust the min and max parameter values of Map to match the MIAC ones.

Posted: **Tue May 30, 2017 4:31 pm**

Hi LeighM
Have tried but no luck

Please see the following update file:

MIACdsPIC-LawnMower-004.fcfx: (20.03 KiB) Downloaded 340 times

Is that what you mean?
I'm not sure what you mean!

Posted: **Wed May 31, 2017 11:33 am**

Try this ....

MIACdsPIC-LawnMower-005.fcfx: (19.2 KiB) Downloaded 391 times

Posted: **Wed May 31, 2017 12:21 pm**

Hi LeighM
Result from practice driving with RC servo tests

Ouput from RC servo is 800
Displayed in display:
MAP value = 255
TSUM value = 3523

Ouput from RC servo is 2200
Displayed in display MAP value = 130
TSUM value = 1517

Servo: Output display should be:
800 - 0 bit
2200 - 255 bit
What should be done to show this result?

Posted: **Wed May 31, 2017 12:40 pm**

Looks like we have an overflow on a variable
try this ...

MIACdsPIC-LawnMower-006.fcfx: (19.2 KiB) Downloaded 348 times

Posted: **Wed May 31, 2017 2:07 pm**

Hi LeighM
Thank you for your suggestion but it did not change the result on the output display.
OK with overflow on a variable.
Ouput speech has not changed.
MAP value is still as from last post
TSUM value is still as from last post

Posted: **Wed May 31, 2017 2:44 pm**

Can you get some more values (of tsum and the servo) between the two limits, 800 (3523) and 2200 (1517)

Posted: **Wed May 31, 2017 3:20 pm**

Hi LeighM

Servo: Output display:
800 - 255 bit
935 - 0 bit
1147 - 30 bit
1351 - 194 bit
1827 - 255 bit
1930 - 0 bit
I can not get some more values (of tsum and the servo) between the two limits, 800 (3523) and 2200 (1517)

Matrix user forums

MIAC-RC LawnMower

MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower

Re: MIAC-RC LawnMower