Matrix user forums

Hello,

Here is the answer !

Benj already answer for this problem : Parameters (16-bit PIC): -P$(chip) -F$(target).hex -E -M -L

It 's the same configuration as Pickit3

http://www.matrixmultimedia.com/mmforums/viewtopic.php?f=53&t=12708&p=50849&hilit=pickit3+not+working#p50830

Next time I will ...

Hello,

I used to program Microchip pic24FJ128GA010 with Explorer 16 via Flowcode . The only thing to do in to configure correctly the programmer and parameters for ICD3. (i.e : ICD3CMD.exe with -P%p - E -F%f.hex -M -Y -L)
But with the new realease of Flowcode V6.0.7 the ICD3 programmer doesn't find ...

Hello Benj , Medelec35

Thanks for your answer, sorry because mine is late.

First I test "Digital Frequency Counter" ,so it works well .I analyse how this counter was bulid .So I saw that It counts every Hertz .
When you use it alone it' OK, but when you install this code inside another it slows ...

Hello,

I have some problems to use capture function with timer1. Iwork with matix development board EB006-00-7 and pic 16F877A.
My goal is to mesure square signal of 10Hz ,given by a signal generator on every rising edge.
For this, I chose to use capture fonction to read timer1 values ,I mean ccp1l ...

hello Ben

I copied the file you sent me in the dirctory and the results are better:

For a programmed baude rate of 100kHz ,i read 94.5kHz on my oscilloscope.
For a programmed baude rate of 400kHz ,i read 327kHz on my oscilloscope.

Little detail i had to change pull_up resistors from 1.8kOhms to 3 ...

hello Ben,

I want to control a device that communicate with I2C bus.So I made my eblock (for EB006V7) to place pull-up resistors (1.8K Ohms) to make the bus working.
I made the programm with Flowcode V4 ,and all is working well .

But as I am a curious man I put my oscilloscope probe on SDC ( the ...

hello ,

I want to use I2C communication on EB006V7 with a PIC 16F877A with a clock at 19660800Hz.
Flowcode I2C windows propose to me 3 baute rates preset values 100KHz,400kHz and 1MHz.
I choose a baute rate of 400KHz, but when i look at the scl signal clock with my oscilloscope the frequency was ...

Hello,

I would like to thank you ,that what i was looking for !

Stephan

Hello ,

I saw one post about the use of Pickit3 talking about compiler options like:

"
Set the Programmer location to: C:\Program Files\Matrix Multimedia\Flowcode V4\Tools\PICkit3\pk3cmd.exe
Set the Programmer parameters to:-P%p -F%f.hex -E -M -Y
"

I wanted to know , where could i find datsheet ...

Hello Stephan

Open the datasheet of your Pic (16F887 eg) with Foxit (or Acrobat).
Click on bookmark , and you will see : chapter 15 : Instruction Set Summary (p239).
You will find all Pic instructions.

Daniel

Thank you Daniel

It seems to be the same text as the course of Bert van Dam .But it ...

Thank you for answering Benj

But I think you don't understand really my question

In fact I purchase Distance learning course pack (EB 4000 and EB742) .So i decided to learn Flowcode with this.

In page 61 Bert van Dam present the first mnemonic 'MOVLW' (figure 55) with an extract of datasheet ...

Hello,

I'm learning about Flowcode with "Distance learning Course" ,multiprogrammer and e-block for it.
The first course are talking about Assembly.
Bert Van Dam discribes mnemonics from an extract of datasheet ,but i can't find the full datasheet about mnemonics because Assembly from Microchip is ...