Matrix user forums

Thanks Benj,

I tried to do just what you did last night and I could not get the flash macro to appear in the call stack. What did I do wrong in the creation of the macro? I really appreaciate all of the work that you do on this forum , but I really do wish that there was a Flowcode for dummies ...

Benj,

Thanks for the new code but I have one more question. In my orginal code I ramped the led up to 50 % then flashed it before ramping back down. I tried to put the flash in the main code but that didn't work so I then tried it in the ramp up macro but I do not get the flash . can you steer me ...

Thanks Benj. Your support is the best ! Thanks a bunch!

Regards,

J Walthall

I am a newbie here using flowcode and I have a question on the code that I have written. I am ramping up a LED flashing it and ramping it back down . My problem is that the LED still has a low glow after it has been ramped down. Is this a code issue or a hardware issue. I am driving the LED from the ...

Thanks Benj that fixed my problem.


Jim Walthall

Hi Benj,

I am using version 3.4.7.48 .

Whenever I choose a 12F683 chip, my flowcode crashes and will not run. It does not do this with any other chip so I am assuming that the chip file is corrupt. What is the best method for correcting this issue.

Thanks !

Jim Walthall

Hello,

I have a problem when I choose a 12F683 chip my Flowcode crashes. Is this a corrupt fcf file ? If so where can I get a new 12F683 .fcf to replace my corrupt one. also can I just delete and paste the new file in the directory?


Thanks,

J Walthall

Hi Benj,

I want to read a signal from a radio control receiver. I really don't understand what I need to read as the signal has a range of 1ms to 2ms pulse. There is no high or low value.

Thanks,

Jim Walthall

Ok I am asking for help again. I am trying to read a RC imput to switch on and off an output on a 12F629 PIC. Is there any sample code out there that I can see to try and figure this out. All I want to do is set the pin high when the PIC sees the 2 ms signal and then low when it see anything else ...

Thanks Steve and Benj . This is a great forum as no question goes unanswered. I did cut and past last night and things worked fine but I did not need to move any Macros. Wil try that later. Once again thanks for the help.

I have another newbie question. I have two programs that I want to merge into one program. What are the proceedures to do this or do I have to rewrite one of the programs into the other.

Thanks !

Jim Walthall

Hi Ben,

Thanks for the insite I have FlowCode up and running with my PIC5 board. It was just as simple as pointing FlowCode programmer to the PIC 5 software. Thanks again !!

I have had FlowCode for some time but have not had the time to do much learning so I am really a Newbie to this software. I would like to use a Mikroelektronika EasyPIC5 development board with FlowCode. Has this been done by anyone and if so can you please walk me thru what I need to do to use this ...

Sean,

Sorry for the delayed reply as I have been out and not able to check this forum. Thanks for the code this helps a bunch!!


Regards,

J Walthall

Hi sean,

Here is what I have . If I use a 720 CPR encoder I will have 2 pluses per deg. I will then need the display to read 00.0 to 99.9 . I would also need some guidance on how to reset the display to zeros with a button on an input pin. Also I am unclear of the input pins for the encoder.This ...

Sean,

Thanks for the reply. Yes I agree that this is not the best thing for me right now. I will figure out the encoder pulses and get back to you. I would really appreciate your help on this as I need to get this project going and this is the part that is slowing things up. I am sure that once I ...

Fixed my chip display problem. Screen on laptop not configujred correctly.

JWalthall

Hi Sean,

Thanks for the information. can you tell me have you tried to open this Encoder2.fcf file that was posted? Why I ask is I cannot get the chip to show up on my screen. When I go to the view menu it shows the chip is checked . I uncheck it and then recheck but the chip does not show up. Any ...

Hello,

I am a new user and new to programming microcontrollers so I am really lost. I need to develop a display that will read an encoder and display the counts on either an LCD or quad 7 segment LED. I have found a thread where some one posted reading an encoder and displaying it on a LCD but I ...