Matrix user forums

Sorry for late reply, I tested and have no trigger from INT/SQW.

Just received my buspirate this week and will test the I2C analysys tool

PERFECT !

That's great & fast service Ben !

Many thank's,

PS : Tested and working

Hello all, Is there a limitation in the number of values to write to internal EEPROM at once ? I have 250 values to write 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 4, 5, 6, 7, 8, 8, 9, 10, 11, 13, 14, 15, 16, 18, 19, 20, 22, 23, 25, 27, 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48, 50, 53, 55, 57, 60, 62...

Thanks Ben

Hello Ben, Just tested your file, and here's the result err.jpg Always the same warning ! I now switched to a 18F4455 because I needed more place and my same code (with change of config) works. For me I'm pretty sure it's a problem between mloader and my EB006 board, I flashed some weeks ago the PIC...

And do you have some news about mloader and the firmware of the EB006-V9 board ?

Hello,

I just tested the component and it's easy to use but unfortunately gives the same error.

With PicKit its' fine

Regards,

Hi Ben,

I allways use the #pragma DATA _EEPROM, in the Supplementary Code block.

If you explain me where I can find the "new "initial values" property" then I can test it here.

Sorry, but I didn't find any documentation about this new feature

Regards,

Hello, Can we please have some status feedback about mloader and EB006-V9 Firmware ? I have troubles with programming the internal EEPROM of the pic's (see post http://www.matrixmultimedia.com/mmforums/viewtopic.php?f=2&t=14895) I invested in FC6 and the new EB006-V9 board last month but I have ...

Hello,

Do you have some news

What's the status about mloader and the EB006-V9 board ?

Regards,

hyperion007 wrote:Crenwick, could you please try the alarm functions as well? I cannot seem to get them working. I have tried both alarms, and many different settings but still nothing.

Ok, I will test it

Hi Jordy, I find the problem :wink: Each time you configure the SQW rate you set also bit 7 (adding 0x80) who is disabling oscillator when on Vbat. Actual Macro, case 2: { //Comment: //Enable Square Wave Output //Frequency = 1Hz FCD_005f1_I2C_Master1__TransmitByte( 0x80 ); break; } case 3: { //Comme...

No problem Jordy

Take your time !

Hi Jordy,

I'm using your component in my project and I'm facing a problem, when I power off the board the clock stay at the same time. It's like bit EOSC is set.

I supposed you cleared this bit with initializing macro ? Right ?

Regards,

The standard delivered quartz on EB006 board is a 19.6608Mhz . That should match the settings in Flowcode.

Can you test this file ?

I removed the bluetooth component and changed pic to 16f1937.

LCD works on my board without problem with this code.

One thing also, I had to rename your file because of " ' " sign not recognized by compiler.

Witch PIC are you using, you can attach your .fcf file if you want so we can test it.

Hello

Do you use the EB005 lcd display or a custom ?

When you use the EB005 (DEFAULT jumpers set) then connections are by default set to PortB (0-Bit0,1-Bit1,2-Bit2,3-Bit3,4-RS,5-E) when using component.

My bed is to re-check these six connections.

Regards,

Hello, I will look into the programming of the 18F4680 EEPROM into the v9 boards. Im not sure if we have one of those chips kicking around but i will check. Ben is away for three weeks, hes been away a couple already he will be back some time next week i believe. Hi, I'm using a 16F887 not a 18F468...

Hello, Does someone tested programming the internal EEPROM of PIC with the new EB006V9 board ? Like I describe in this topic, I'm unable to do it because of error. http://www.matrixmultimedia.com/mmforums/viewtopic.php?f=54&t=14886 But when I take the hex and write it with another programmer it'...

Some update !

I used the ramptest.hex with my pickit2 and it was programmed successfully !

So I presume we have a problem with mloader and/or EB006V9

Hi all, I'm testing some RGB curves for my project and made a simple program to test these curves (see attach). Problem is when I try to write the values in EEPROM at programming. I added some values to the EEPROM via the "supplementary code" option. I changed also the #pragma DATA _EEPROM...

Done !

Problem solved.

Just a question, what was the other problem/fix ?

Hi Leigh,

That's perfect ! Works now fine

@ Matrix Staff

Can you please check this component ? I'm blocked in my project due to this problem.

Sorry for the stress, I suppose you're all busy or maybe some colleagues are out of office