Component: DAC (MCP48x1) (MCP48x1) (Analog Output)

Author	Matrix TSL
Version	1.0
Category	Analog Output

DAC (MCP48x1) component

Component to drive a digital to analogue converter (DAC) IC from Microchip via an SPI interface. Compatible with MCP4801 (8-Bit), MCP4811 (10-Bit) and MCP4821 (12-Bit) devices.

Detailed description

No detailed description exists yet for this component

Examples

No additional examples

Downloadable macro reference

	SetOutput
Sets the output voltage of the DAC 8-Bit: Range 0-255 10-Bit: Range 0-1023 12-Bit: Range 0-4095
- UINT	DAC_Value
The value to output to the DAC
- VOID	Return

	ControlPins
Allows Shutdown (SHDN) and Latch (LDAC) pins to be controlled directly if enabled.
[[File:]] -	Shutdown
0 = Shutdown Device, 1 = Device Active
[[File:]] -	Latch
0 = Data output driven from DAC register, 1 = Data output locked
- VOID	Return

	Disable
Disables the DAC output.
- VOID	Return

	Enable
Enables the DAC Output.
- VOID	Return

	Initialise
Configures the SPI peripheral ready for communications and initialises the internal variables. DAC needs to be enabled before any output voltage can be generated.
- VOID	Return

	Initialise
Configures the SPI peripheral ready for communications and initialises the internal variables. DAC needs to be enabled before any output voltage can be generated.
- VOID	Return

	WriteLEDs
Allows control of all 8-LEDs on the front of the Formula Flowcode.
- BYTE	LED_Byte
- VOID	Return

	Initialise
Starts up the formula flowcode PWM for motor control and performs the wait for button press
- VOID	Return

	Initialise
The Init macro must be called once to initialise the Graphical LCD display before any other Graphical LCD component macros are called.
- VOID	Return

	Initialise
The Init macro must be called once to initialise the Graphical LCD display before any other Graphical LCD component macros are called.
- VOID	Return

	Initialise
The Init macro must be called once to initialise the Graphical LCD display before any other Graphical LCD component macros are called.
- VOID	Return

	Initialise
The Init macro must be called once to initialise the Graphical LCD display before any other Graphical LCD component macros are called.
- VOID	Return

	Initialise
Resets and initialises the Internet E-Block. It sets up the gateway address, subnet mask, device IP address and device MAC address as defined in the properties of the Flowcode component. This macro must be called before any other TCP_IP component macros
- VOID	Return

	Initialise
Resets and initialises the Internet E-Block. It sets up the gateway address, subnet mask, device IP address and device MAC address as defined in the properties of the Flowcode component. This macro must be called before any other TCP_IP component macros
- VOID	Return

	Initialise
Resets and initialises the Internet E-Block. It sets up the gateway address, subnet mask, device IP address and device MAC address as defined in the properties of the Flowcode component. This macro must be called before any other TCP_IP component macros
- VOID	Return

	MODPMSHAPE
Sets PM waveform shape to; 0 = SINE, 1 = SQUARE, 2 = RAMPUP, 3 = RAMPDN, 4 = TRIANG, 5 = NOISE, 6 = DC, 7 = SINC, 8 = EXPRISE, 9 = LOGRISE, 10 = ARB1, 11 = ARB2, 12 = ARB3, 13= ARB4.
- BYTE	Shape
Sets PM waveform shape (1 = SINE, 2 = SQUARE, 3 = RAMPUP, 4 = RAMPDN, 5 = TRIANG, 6 = NOISE, 7 = DC, 8 = SINC, 9 = EXPRISE, 10 = LOGRISE, 11 = ARB1, 12 = ARB2, 13 = ARB3, 14= ARB4).
- VOID	Return

	ARB4
Loads the binary-data to an existing arbitrary waveform memory location ARB4.
- BYTE	Waveform
- VOID	Return

	CLKSRRet
Returns the clock source <INT> or <EXT>.
[[File:]] -	Return

	MODPMDEV
Sets PM waveform deviation to <nrf> degrees. (Lower limit: -360° - Upper limit: 360°).
[[File:]] -	Degrees
Sets PM waveform deviation in degrees (-360 - 360).
- VOID	Return

	MSTLOCK
Sends signal to SLAVE generator to get synchronised
- VOID	Return

	HILVL
Sets the amplitude-high-level to <nrf> Volts. (Lower limit: -0.490 V - Upper limit: 5.000 V).
[[File:]] -	HighLevel
Sets the amplitude-high-level in Volts(V) (-0.490 V - 5.000 V).
- VOID	Return

	ARB3
Loads the binary-data to an existing arbitrary waveform memory location ARB3.
- UINT	Waveform
- VOID	Return

	WAVE
Sets the waveform type. 0 = SINE, 1 = SQUARE, 2 = RAMP, 3 = TRIANG, 4 = PULSE, 5 = NOISE, 6 = ARB
- BYTE	WaveType
0 = SINE, 1 = SQUARE, 2 = RAMP, 3 = TRIANG, 4 = PULSE, 5 = NOISE, 6 = ARB.
- VOID	Return

	CALADJ
Adjust the selected calibration value by <nrf> (Lower limit: -100 - Upper limit: 100).
[[File:]] -	Calibrate
Adjust the selected calibration value (-100 - 100).
- VOID	Return

	STBRet
Returns the value of the Status Byte Register in <nr1> numeric format.
- BYTE	Return

	ARB2
Loads the binary-data to an existing arbitrary waveform memory location ARB2.
- UINT	Waveform
- VOID	Return

	EERRet
Query and clear execution error number register.
- STRING	Return

	MODFMSRC
Sets FM waveform source to; 0 INT, 1 = EXT.
[[File:]] -	Source
Sets FM waveform source (0 = INT, 1 = EXT).
- VOID	Return

	MODAMFREQ
Sets AM waveform frequency to <nrf> Hz. (Lower limit: 1uHz - Upper limit: 20kHz).
[[File:]] -	Frequency
Sets AM waveform frequency in Hertz(Hz) (1uHz - 20kHz).
- VOID	Return

	ESE
Sets the Standard Event Status Enable Register to the value of <nrf>.
- BYTE	Value
Value of register 0-255
- VOID	Return

	ARB1
Loads the binary-data to an existing arbitrary waveform memory location ARB1.
- UINT	Waveform
16 Bit binary number for arbitrary waveform.
- VOID	Return

	ARB4DEFRet
Returns user specified waveform name, waveform pint interpolation state and waveform length of ARB4.
- STRING	Return

	CLS
Clears status byte register of the interface.
- VOID	Return

	MSTRELOCK
Resynchronises the two generators in MASTER-SLAVE mode.
- VOID	Return

	NOISLVL
Sets the output noise level to <nr1> %. (Lower limit: 0% - Upper limit: 50%)
- BYTE	Percent
Sets the output noise level in percent. (0 - 50)
- VOID	Return

	LOCKMODE
Sets the synchronising mode to; 0 = MASTER, 1 = SLAVE, 2 = INDEP.
- BYTE	Mode
Sets the synchronising mode (0 = MASTER, 1 = SLAVE, 2 = INDEP).
- VOID	Return

	ADDRESSRet
Returns the instruments address
[[File:]] -	Return

	MODPMSRC
Sets PM waveform source to; 0 INT, 1 = EXT.
[[File:]] -	Source
Sets PM waveform source (0 = INT, 1 = EXT).
- VOID	Return

	MODPWMSRC
Sets PWM waveform source to; 0 = INT, 1 = EXT.
[[File:]] -	Source
Sets PWM waveform source (0 = INT, 1 = EXT).
- VOID	Return

	MOD
Sets modulation to; 0 = OFF, 1 = AM, 2 = FM, 3 = PM, 4 = FSK, 5 = PWM.
- BYTE	Modulation
Sets modulation (0 = OFF, 1 = AM, 2 = FM, 3 = PM, 4 = FSK, 5 = PWM).
- VOID	Return

	ISTRet
Returns IST local message as defined by IEEE Std. 488.2. The syntax of the response is 0<rmt>, if the local message is false, or 1<rmt>, if the local message is true.
[[File:]] -	Return

	LRNRet
Returns the complete setup of the instrument as a binary data block
[[File:]] -	Return

	OPCRet
Query Operation Complete status. The response is always 1<rmt> and will be available immediately the command is executed because all commands are sequential.
[[File:]] -	Return

	SWPTYPE
Sets the sweep type to; 0 = LINUP, 1 = LINDN, 2 = LINUPDN, 3 = LINDNUP, 4 = LOGUP, 5 = LOGDN, 6 = LOGUPDN, 7 = LOGDNUP.
- BYTE	Type
Set the sweep type (0 = LINUP, 1 = LINDN, 2 = LINUPDN, 3 = LINDNUP, 4 = LOGUP, 5 = LOGDN, 6 = LOGUPDN, 7 = LOGDNUP).
- VOID	Return

	PULSRANGE
Sets PWM waveform source to <1>, <2> or <3>; 1 = 1, 2 = 2, 3 = 3.
- BYTE	Range
Sets the pulse rise and fall range. (1, 2 or 3)
- VOID	Return

	TSTRet
The generator has no self test capability and the response is always 0 <rmt>.
[[File:]] -	Return

	BSTTRGPOL
Sets the burst trigger slope to; 0 = POS, 1 = NEG.
[[File:]] -	Slope
Set the burst trigger slope (0 = POS, 1 = NEG).
- VOID	Return

	ARB3Ret
Returns the binary-data from an existing abbitrary wavefrom memory location.
- UINT	Return

	BSTPHASE
Sets the burst phase to <nrf> degrees. (Lower limit: -360 - Upper limit: 360)
[[File:]] -	Degrees
Sets the burst phase in degrees (-360 - 360)
- VOID	Return

	IDNRet
Returns the instrument identification. The IDN is saved to the variable passed from the function 'ReturnIDN'. The return parameter is TRUE when the IDN is successfully returned.
- STRING	ReturnIDN
- STRING	Return

	SWPTRGPER
Sets the sweep trigger period to <nrf> seconds
[[File:]] -	Seconds
Set the sweep trigger period in seconds.
- VOID	Return

	PULSDLY
Sets the waveform delay to <nrf> sec
[[File:]] -	Sec
- VOID	Return

	Initialise
Opens the COM port ready for communications.
- VOID	Return

Property reference

	Properties
	DAC IC
Selects which DAC IC is connected and therefore the bit depth available.
	Gain Option
Selects the maximum reference value for the DAC
	Vref Voltage
Reference Voltage, Used to calculate the Voltage resolution.
	Steps
Number of discrete output states available from the DAC.
	Control Bits
Number of digital control bits
	Resolution
Maximum output resolution based on number of control bits.
	Voltage Resolution
Specifies the Resolution per digital bit in terms of Voltage.
	Channel
SPI Channel selector
	Prescale
Prescale option selector
	MOSI
SPI Data Out Pin SDO - Also Known as Master Out Slave In (MOSI) when used in Master mode.
	MISO
SPI Data In Pin SDI - Also Known as Master In Slave Out (MISO) when used in Master mode.
	CLK
SPI Clock Pin CLK - The Clock signal is driven by the SPI master.
	CS / SS
Chip Select / Slave Select Pin Master Mode: General purpose output pin used to select the remote SPI device. Slave Mode: Hardware chip select pin input used to select the SPI device.
	Use SHDN Pin
Allows the SHDN pin to be driven from an output pin on the microcontroller. If not used then tie the SHDN pin to VCC to allow the DAC to function.
	Use LDAC Pin
Allows the LDAC pin to be driven from an output pin on the microcontroller. If not used then tie the LDAC pin to GND to allow the DAC to function.
	Connections
	Simulations
	Simulate Comms
	DAC Output Scope Trace
Selects if the scope traces are automatically generated or not
	SPI Scope Traces
Selects if the scope traces are automatically generated or not
	SPI Console Data
Selects if the console data is automatically generated or not
	API