Component: Switch Array (Push) (Switches)

From Flowcode Help
Revision as of 13:14, 7 February 2023 by Wiki bot (talk | contribs)
Jump to navigationJump to search
Author Matrix Ltd.
Version 2.0
Category Switches


Switch Array (Push) component

An array of up to eight momentary push switches, each connected to a single pin of the specified port.

Component Source Code

Please click here to download the component source project: FC_Comp_Source_switch_array_push.fcfx

Please click here to view the component source code (Beta): FC_Comp_Source_switch_array_push.fcfx

Detailed description

No detailed description exists yet for this component

Examples

Here is an example Flowcode program to read the values of a switch array. FC6 Icon.png Switch Array


Here is a schematic of how to connect a basic switch to a microcontroller pin.

Switchschematic.jpg

The active high circuit will pass a logical 0 to the input pin when the switch is not pressed and a logical 1 when the switch is pressed.

The active low circuit will pass a logical 1 to the input pin when the switch is not pressed and a logical 0 when the switch is pressed.


There are some differences depending on the type of switch you have, the above states assume a generic push to make type switch, however a push to break type switch would have reversed logic and a toggle switch can work well with either setup.


The resistors are required for correct operation because when a microcontroller's input pin is essentially connected to nothing it will pick up noise in the environment and provide inconsistent readings. This state is referred to as floating i.e. the pin is floating. To test this remove the resistors (if possible) and touch the unconnected pin with your finger the output LED from the example file above will toggle on and off at high speed.


Any values of resistor can be used but it is important to keep the smaller resistor at least 10X smaller then the larger resistor to ensure that the pressed state provides at least 0.91% of the required pressed state voltage. For example a active high switch circuit using 1K and 10K resistors should pull up to about 4.54V when the switch is pressed.

(5V / 11K) * 10K = 4.54545V






Macro reference

GetHandle

Fc9-comp-macro.png GetHandle
Retrieves the object handle of the switch component at the given index. 
Fc9-u8-icon.png - BYTE Index
 
Fc9-h32-icon.png - HANDLE Return


ReadAll

Fc9-comp-macro.png ReadAll
Reads all of the switches at once, returning a byte containing one bit per switch. 
Fc9-u8-icon.png - BYTE Return


ReadState

Fc9-comp-macro.png ReadState
Read the state of the switch at the given index. 
Fc9-u8-icon.png - BYTE Index
The switch to read the status of. 
Fc9-bool-icon.png - BOOL Return


WaitUntilHigh

Fc9-comp-macro.png WaitUntilHigh
Pause the program until the switch at the given index is turned on. 
Fc9-u8-icon.png - BYTE Index
Index of the switch to wait for. 
Fc9-void-icon.png - VOID Return


WaitUntilLow

Fc9-comp-macro.png WaitUntilLow
Pause the program until the switch at the given index is turned on. 
Fc9-u8-icon.png - BYTE Index
Index of the switch to wait for. 
Fc9-void-icon.png - VOID Return


Property reference

Fc9-prop-icon.png Properties
Fc9-type-16-icon.png Count
The number of LEDs in the array from 1 to 8. 
Fc9-conn-icon.png Connections
Fc9-type-16-icon.png Input Mode
Choose a single port for all LEDs - pins are allocated in sequence from pin 0 - 7 ...or choose 'Custom pins' to assign each switch individually. 
Fc9-type-19-icon.png Port
 
Fc9-type-16-icon.png Polarity
Active High = LEDs light when the chosen chip pin is ON Active Low = LEDs light when the chosen chip pin is OFF 
Fc9-type-14-icon.png Debounce
Time in milliseconds allowed for the pin to settle following a change of state. 
Fc9-type-16-icon.png Operation
Sets whether switches toggle or are press/release. NB) This option can only be set when the original target includes this option. 
Fc9-conn-icon.png Simulation
Fc9-type-16-icon.png Alignment
Which 3D axis to align the copies along. 
Fc9-type-15-icon.png Spacing
The distance between LEDs in the array. LEDs will be spaced symmetrically around the component centre. Use a negative value to reverse the order of the LEDs. 
Fc9-type-7-icon.png Reverse
Whether to reverse the order of the switches. 
Fc9-type-16-icon.png Show Labels
Whether to show labels giving each switch's pin connection. 
Fc9-type-1-icon.png Label color
Color of the port and pin labels