Component: Data Transfer (API I2C) ()

Author	Matrix Ltd
Version	1.2
Category

Data Transfer (API I2C) component

Comms data injector to allow a I2C bus peripheral to be attached to a comms component. The component will forward any byte transactions through to a SCADA Slave enabled hardware. Enabling the Flowcode simulation runtime to directly drive a physical I2C bus.

Detailed description

No detailed description exists yet for this component

Examples

No additional examples

Downloadable macro reference

	InitialiseInjector
Sets up the injector ready to receive commands or send data
- STRING	InjectorName
Name of the console that will be created
- BYTE	Return

	TxByte
Puts a byte onto the comms channel.
- BYTE	DataByte
- VOID	Return

	RxByte
Attempt to receive a byte back from the injector 0 - 255 = Valid data 256 = RX timeout no data available
- UINT	Return

	GetConsoleHandle
Gets the handle to the console allowing data displaying on the panel etc.
[[File:]] -	Return

	ChangeState
Sets the state of the bus. SPI - Controls the chip select pin I2C - Controls the start/restart/stop status
- BYTE	State
SPI: 0=CSLow, 1=CSHigh I2C: 0=Stop, 1=Start, 2=Restart, 3=LastRx
- VOID	Return

	UARTSend
- BYTE	Channel
- BYTE	Data
- VOID	Return

	Initialise
Sets up the GSM module. Returns 0 for OK, 255 for no reply and 254 for command fail.
- BYTE	Return

	SampleAccel
Samples the accelerometer 0 = no new data, 1 = new data available
- BYTE	Return

	Left
Rotates the robot left - waits for the angle to be traversed before returning
- UINT	Angle
Angle to turn in degrees
- VOID	Return

	ReadIR
Reads an IR sensor 0=Left, 1=FrontLeft, 2=Front, 3=FrontRight, 4=Right, 5=RearRight, 6=Rear, 7=RearLeft
- BYTE	index
0=Left, 1=FrontLeft, 2=Front, 3=FrontRight, 4=Right, 5=RearRight, 6=Rear, 7=RearLeft
- UINT	Return

	LCDDrawPixel
Allows a single pixel on the LCD to be set or cleared
- BYTE	X
X Pixel 0-127
- BYTE	Y
Y Pixel 0-31
- BYTE	State
0=White (Off), 1=Black (On)
- VOID	Return

	ServoSetPosition
Allows one of the servo positions to be assigned
- BYTE	Channel
Range 0-3
- BYTE	Position
Range 0-255
- VOID	Return

	CardBitmap
Displays a monochrome bitmap read from the card on the LCD
- BYTE	X
Range 0-127
- BYTE	Y
Range 0-31
- STRING	Filename
- BYTE	Return

	CardRecordMic
Records an audio stream on the card from the microphone
- BYTE	BitDepth
0=8-bit, 1=16-bit
- BYTE	SampleRate
Sample Rate 0=8KHz, 1=16KHz
- UINT	RecordTime
Time to record for in seconds, Range 0-65535
- STRING	Filename
- BYTE	Return

	CardOpen
Attempts to open an existing file on the SD card 255=Error, 1=File not found, 0=Open OK
- STRING	Filename
- BYTE	Return

	Forwards
Drives the robot forwards - waits for the distance to be traversed before returning
- UINT	Distance
Distance in mm
- VOID	Return

	ReadBearing
Reads the compass bearing based on the degrees clockwise from magnetic north.
[[File:]] -	Return

	GetConsoleHandle
Gets the handle to the console allowing data displaying on the panel etc.
[[File:]] -	Return

	LCDDrawLine
Allows a single pixel width line to be drawn on the LCD
- BYTE	X1
X Pixel 0-127
- BYTE	Y1
Y Pixel 0-31
- BYTE	X2
X Pixel 0-127
- BYTE	Y2
Y Pixel 0-31
- VOID	Return

	ServoAutoMoveToPosition
Allows one of the servo positions to move gradually to a new position
- BYTE	Channel
Range 0-3
- BYTE	Position
Range 0-255
- VOID	Return

	ReadAllValue
Reads a single value stored from the read all command Index dictates which sensor value to read
- BYTE	Index
0=SW, 1-8=IR, 9-10=Line, 11=Light, 12=Mic, 13-15=Accel
- UINT	Return

	LCDBacklight
Allows the LCD backlight brighntess to be adjusted
- BYTE	Intensity
Range 0-100, 0=Off, 1=Min Brightness, 100=Max Brightness
- VOID	Return

	LCDDrawRect
Allows a rectangle to be drawn on the LCD
- BYTE	X1
X Pixel 0-127
- BYTE	Y1
Y Pixel 0-31
- BYTE	X2
X Pixel 0-127
- BYTE	Y2
Y Pixel 0-31
- VOID	Return

	ReadLine
Reads one of the IR line sensors 0-1 0=Left, 1=Right
- BYTE	index
0=Left, 1=Right
- UINT	Return

	ServoDisable
Allows one of the servo outputs 0-3 to be disabled
- BYTE	Channel
Range 0-3
- VOID	Return

	ServoEnable
Allows one of the servo outputs 0-3 to be enabled
- BYTE	Channel
Range 0-3
- VOID	Return

	CardReadByte
Reads a byte from the currently open file. Starts at the beginning of the file and auto increments to the end
- BYTE	Return

	CardErase
Attempts to delete an existing file on the SD card 255=Error, 1=File not found, 0=Delete OK
- STRING	Filename
- BYTE	Return

	CardWriteByte
Appends a byte to the end of the currently open file
- BYTE	Data
- VOID	Return

	EncoderRead
Reads one of the motor encoder counters. Approx 0.328296mm of travel per encoder unit.
- BYTE	index
0=Left, 1=Right
- UINT	Return

	SetMotors
Sets the motor speeds without feedback Range -100 to 100
[[File:]] -	Left
Range -100 to 100
[[File:]] -	Right
Range -100 to 100
- VOID	Return

	Backwards
Drives the robot backwards - waits for the distance to be traversed before returning
- UINT	Distance
Distance in mm
- VOID	Return

	EncoderReset
Resets the motor encoder counters
- VOID	Return

	LCDVerbose
Allows the LCD to automatically report the API commands as they get processed. Default - verbose on
- BYTE	State
0=Off 1=On
- VOID	Return

	SetProp
Allows the COM port property to be set from a parent component.
- STRING	PropName
- ULONG	PropVal
- VOID	Return

	CardInit
Attempts to startup the SD card 255=No Card, 254=Init Fail, 0=Init OK
- BYTE	Return

	GetProp
Allows the property filter for the COM port list to be copied to a parent component.
- STRING	PropName
- STRING	Return

	LCDClear
Clears the LCD
- VOID	Return

Property reference

	Properties
	SCADA Slave
SCADA Slave component to use to pipe data to a physical SPI bus
	Connections
	Simulations