Component: IO Expander (Comms: System)

Author	Matrix TSL
Version	1.0
Category	Comms: System

IO Expander component

Provides 16 digital input/output pins arranged into two 8-bit ports using a SPI bus connection. Multiple expanders can be connected to the same SPI peripheral by means of individual chip select pins.

Detailed description

No detailed description exists yet for this component

Examples

More information on I2C can be found here,

Matrix Flowcode Blog: Simplified communications I2C and SPI

Generic I2C EEPROM

Example file demonstrating how to read and write bytes from a generic I2C EEPROM device. I2CEEPROM

Downloadable macro reference

	ReadPort
Reads a value to one of the ports with a mask. Configures the masked bits to be inputs before reading the input value.
- BYTE	Port
0=PortA, 1=PortB
- BYTE	Mask
Allows port bits to be modified without effecting other bits, 255 = write full port.
- BYTE	Return

	ConfigureInversion
Configures the pin inversion for the two ports. Disabled on all pins by default.
- BYTE	PortA
Port A inversion sent as an 8-bit value, 0 = Disabled, 1 = Enabled
- BYTE	PortB
Port B inversion sent as an 8-bit value, 0 = Disabled, 1 = Enabled
- VOID	Return

	ReadPortPin
Reads a single port pin from one of the ports. Configures the pins to be an input before reading the input value. Returns 0 or 1 corresponding to the value on the port pin.
- BYTE	Port
0=PortA, 1=PortB
- BYTE	Pin
Port pin to read. Range: 0-7
- BYTE	Return

	WritePortPin
Writes a single port pin on one of the ports. Configures the pins to be an output before writing the input value.
- BYTE	Port
0=PortA, 1=PortB
- BYTE	Pin
Port pin to read. Range: 0-7
- BYTE	Value
Value to output on the selected pin. Range: 0-1
- VOID	Return

	WritePort
Writes a value to one of the ports with a mask. Configures the masked bits to be outputs before writing the output value.
- BYTE	Port
0=PortA, 1=PortB
- BYTE	Mask
Allows port bits to be modified without effecting other bits, 255 = write full port.
- BYTE	Value
Value to write. Range 0-255
- VOID	Return

	ConfigurePullups
Configures the pullups for the two ports. Disabled on all pins by default.
- BYTE	PortA
Port A pull ups sent as an 8-bit value, 0 = Disabled, 1 = Enabled
- BYTE	PortB
Port B pull ups sent as an 8-bit value, 0 = Disabled, 1 = Enabled
- VOID	Return

	ReadRegister
Reads an 8-bit value from a register on the I/O expander device.
- BYTE	Address
Register address to write to. Range: 0-15
- BYTE	Return

	WriteRegister
Writes an 8-bit value to a register on the I/O expander device.
- BYTE	Address
Register address to write to. Range: 0-15
- BYTE	Value
Value to write. Range: 0-255
- VOID	Return

	Initialise
- VOID	Return

	Initialise
- VOID	Return

	Initialise
Enables the I²C hardware and performs some initialization. Should be called at the start of the program or at least before any of the other I²C functions are called.
- VOID	Return

	CheckNetworkStatus
Returns the state of the GSM network. 0 = Not connected, 1 = connected, 255 = no reply from GSM.
- BYTE	Return

	CheckForIncoming
Checks to see if any incoming phone call or SMS message. 0 = Nothing, 1 = Text Received, 2 = Phone Ringing
- BYTE	Return

	Initialise
Sets up the GSM module. Returns 0 for OK, 255 for no reply and 254 for command fail.
- BYTE	Return

Property reference

	Properties
	External Address
Selects the value of the three address pins for the MCP23S17.
	Channel
SPI Channel selector
	Prescale
Prescale option selector
	MOSI
SPI Data Out Pin SDO - Also Known as Master Out Slave In (MOSI) when used in Master mode.
	MISO
SPI Data In Pin SDI - Also Known as Master In Slave Out (MISO) when used in Master mode.
	CLK
SPI Clock Pin CLK - The Clock signal is driven by the SPI master.
	CS / SS
Chip Select / Slave Select Pin Master Mode: General purpose output pin used to select the remote SPI device. Slave Mode: Hardware chip select pin input used to select the SPI device.
	Use Reset
	Connections
	Simulations
	Label
	Scope Traces
Selects if the scope traces are automatically generated or not
	Console Data
Selects if the console data is automatically generated or not
	API