Search found 33 matches
- Wed May 01, 2024 5:08 pm
- Forum: Bug Reports
- Topic: Eeprom compiling generates errors
- Replies: 2
- Views: 75
Re: Eeprom compiling generates errors
Hello Martin, if you take the same program, modify to PIC16F1829, address in uint und return value in byte, it compiles without error? The initial examples values of the component are not cleared. Where is the difference? Wiki says "Comma seperated list of values to assign to the EEPROM memory while...
- Wed May 01, 2024 7:44 am
- Forum: Bug Reports
- Topic: Eeprom compiling generates errors
- Replies: 2
- Views: 75
Eeprom compiling generates errors
Hello!
Can you compile the attached file and look why it`s generating errors?
Regards
Jorg
Can you compile the attached file and look why it`s generating errors?
Regards
Jorg
- Tue Feb 27, 2024 11:07 am
- Forum: Feature Requests
- Topic: Choosing a maximal or smal text box
- Replies: 1
- Views: 470
Choosing a maximal or smal text box
Hello! In the flowchart is the text beside an icon in the wide limited. Beside the C-icon are only 6 lines shown. Can you program a point in the "Options" where to choose that the programming text is shown complete in the flowchart? For the wide you could catch an point on the right side with the mo...
- Fri Feb 23, 2024 5:44 pm
- Forum: General
- Topic: C-File from Version 10 to MPLAB
- Replies: 7
- Views: 422
Re: C-File from Version 10 to MPLAB
Hello!
Thanks for the info.
"Succsessfully compiled" means, that all is OK without errors?
Regards
Jorg
Thanks for the info.
"Succsessfully compiled" means, that all is OK without errors?
Regards
Jorg
- Thu Feb 22, 2024 4:15 pm
- Forum: General
- Topic: C-File from Version 10 to MPLAB
- Replies: 7
- Views: 422
Re: C-File from Version 10 to MPLAB
Hello!
Here is the complete message from MPLAB.
Regards
Jorg
Here is the complete message from MPLAB.
Regards
Jorg
- Wed Feb 21, 2024 11:27 am
- Forum: General
- Topic: C-File from Version 10 to MPLAB
- Replies: 7
- Views: 422
Re: C-File from Version 10 to MPLAB
Hello!
Here is the old file.....
Regards
Jorg
Here is the old file.....
Regards
Jorg
- Wed Feb 21, 2024 8:20 am
- Forum: General
- Topic: C-File from Version 10 to MPLAB
- Replies: 7
- Views: 422
C-File from Version 10 to MPLAB
Hello Matrix team, how can I managed it, to compile a Flowcode C-File in MPLAB? I got a lot of errors. Info: For future the C90 library is discontinued by Microchip. Errors: make -f nbproject/Makefile-default.mk SUBPROJECTS= .build-conf make -f nbproject/Makefile-default.mk dist/default/production/T...
- Mon Jun 27, 2022 6:41 pm
- Forum: Bug Reports
- Topic: BMP280 pressure sensor
- Replies: 10
- Views: 3234
Re: BMP280 pressure sensor
Hello! Here are now some informations about my trials: 01.) The I2C-2 is not working at once. Here I must enable in project options BIT21 (alternate I2C-2) for B5 and B6. 02.) The component have a choose point "mode". In normal mode the modul is running. Changing to "forced" mode reads out no values...
- Wed Jun 22, 2022 5:14 pm
- Forum: Bug Reports
- Topic: BMP280 pressure sensor
- Replies: 10
- Views: 3234
Re: BMP280 pressure sensor
Hello! I tried your hint, but it is not working. By all the trials after more than a minute the software was reading the values, suddenly a value of 2212 is displayed. This could be 22,12 degrees. But I couldn`t reproduced this situation through starting the controller again.. Then I replace the sen...
- Mon Jun 20, 2022 6:45 pm
- Forum: Bug Reports
- Topic: BMP280 pressure sensor
- Replies: 10
- Views: 3234
BMP280 pressure sensor
Hello! Thanks for quick answere. I uses software I2C for starting my first going with the sensor. Temperature and pressure I got back the value "0" ? Reading altitude got`s a value about 12000 ? On the picture you can see the oscilloscoped screenshot of reading the temperature. Address is correct an...