Search found 899 matches
- Thu Apr 04, 2024 6:53 am
- Forum: General
- Topic: SK6812 LED
- Replies: 37
- Views: 3639
Re: SK6812 LED
Something is wrong.... I downloaded Testsk6812 from above - the MCU is set as ATMEGA328PTQFP (is this intended?) Changing the target to ATMEGA328p gives -> Pin0 of component ESP_RMT1 is connected to bit 2 of Port A but this port/bit does not exist on the new microcontroller Flowcode then closes (cra...
- Wed Apr 03, 2024 4:12 pm
- Forum: General
- Topic: SK6812 LED
- Replies: 37
- Views: 3639
Re: SK6812 LED
You also need to call Refresh after doing the setall - to upload the data to the leds
- Wed Apr 03, 2024 9:41 am
- Forum: General
- Topic: SK6812 LED
- Replies: 37
- Views: 3639
Re: SK6812 LED
C:\ProgramData\MatrixTSL\FlowcodeV9\CAL\ESP\ESP_CAL_RMT.c:112:19: error: conflicting types for 'FC_CAL_RMT_TX_1'
CALFUNCTION(void, FC_CAL_RMT_TX_, (void))
Definitely trying to include the esp code?
If the target is a 328p then there is an issue with the component?
Martin
- Wed Apr 03, 2024 8:37 am
- Forum: General
- Topic: SK6812 LED
- Replies: 37
- Views: 3639
Re: SK6812 LED
This is an issue with ESP32 and later versions of the RMT interface.
See the post at viewtopic.php?p=14339#p14339
For a working version - the RMT interface and to have changed dramatically...
Martin
See the post at viewtopic.php?p=14339#p14339
For a working version - the RMT interface and to have changed dramatically...
Martin
- Wed Mar 27, 2024 10:31 am
- Forum: General
- Topic: E-Blocks 2 settings
- Replies: 4
- Views: 1298
Re: E-Blocks 2 settings
If you post your chart - someone will surely be able to help...
Martin
Martin
- Tue Mar 26, 2024 12:14 pm
- Forum: General
- Topic: ESP32 Toolchain.
- Replies: 2
- Views: 1337
Re: ESP32 Toolchain.
I had a bit of a play with 5.2 - but although I could compile from the command line couldn't get it to work from within FC.
So went back to 5.1.2. Which seems to work AOK..
Martin
So went back to 5.1.2. Which seems to work AOK..
Martin
- Fri Mar 22, 2024 10:48 am
- Forum: Bug Reports
- Topic: Lookup table resizing.
- Replies: 4
- Views: 969
Re: Lookup table resizing.
Ok - I'll replace the spaces with commas - odd that it works for the original data block - which also uses spaces....
- Fri Mar 22, 2024 5:42 am
- Forum: Bug Reports
- Topic: Lookup table resizing.
- Replies: 4
- Views: 969
Re: Lookup table resizing.
Yes - a table of 8 bit values.
Not sure if size is limited but the initial size shows correctly and in simulation (which is all that is needed here) seems to work correctly (although I didn't single step through it all - and the simulation locked when I altered the rate slider)
Martin
Not sure if size is limited but the initial size shows correctly and in simulation (which is all that is needed here) seems to work correctly (although I didn't single step through it all - and the simulation locked when I altered the rate slider)
Martin
- Thu Mar 21, 2024 9:16 pm
- Forum: Bug Reports
- Topic: Lookup table resizing.
- Replies: 4
- Views: 969
Lookup table resizing.
I hit a small issue resizing a lookup table (in an Arduino sketch - though this might not be relevant) I created an 8 bit lookup table and pasted in 4637 values - this was correctly reflected in the num values field. However - to create a simpler 'demo' version of my program I then replaced these va...
- Thu Mar 21, 2024 9:08 pm
- Forum: General
- Topic: Protocol j1587
- Replies: 80
- Views: 8452
Re: Protocol j1587
A version that allows multiple 'message blocks' to be read:
Here allowing MIDs of 128 and 144.
Here allowing MIDs of 128 and 144.