I am new to Flowcode and having followed an online tutorial I have built a very simple test project.
When I try to compile it to the target Arduino Nano I get a message stating "You do not have a valid license to perform this action". I have tried all the functions I can find in the HELP tab under licensing, but cannot see a solution.
Any help would be appreciated
License Activation
-
- Posts: 6
- http://meble-kuchenne.info.pl
- Joined: Wed Mar 27, 2024 8:17 am
-
- Valued Contributor
- Posts: 1207
- Joined: Thu Dec 03, 2020 10:57 am
- Has thanked: 293 times
- Been thanked: 424 times
Re: License Activation
It was Nano 328 115200, but I have changed it to Nano 328.
It now compiles, but with the following error.
C:\ProgramData\MatrixTSL\FlowcodeV10\FCD\AVR\batchfiles\avrc_arduinoA.bat reported error code 0x1
I'm not sure what this means though
It now compiles, but with the following error.
C:\ProgramData\MatrixTSL\FlowcodeV10\FCD\AVR\batchfiles\avrc_arduinoA.bat reported error code 0x1
I'm not sure what this means though
-
- Matrix Staff
- Posts: 1481
- Joined: Wed Dec 02, 2020 11:07 pm
- Has thanked: 525 times
- Been thanked: 481 times
Re: License Activation
Hello.
Can you select Full Editor & Preview, below the reply window, Select attachments and upload the .fcfx, .msg.txt and .c files within the project folder.
Without seeing those files we can only guess.
Do you have the nano drivers installed and selected the correct comport (bottom righthand side) from within Build > Project Options...
Can you select Full Editor & Preview, below the reply window, Select attachments and upload the .fcfx, .msg.txt and .c files within the project folder.
Without seeing those files we can only guess.
Do you have the nano drivers installed and selected the correct comport (bottom righthand side) from within Build > Project Options...
Martin
Re: License Activation
Hello Martin,
I do not understand the first question you asked re Full Editor etc. I cannot see this on the forum page
Second question.Nano responds to Arduino IDE upload, so Drivers and Port should be ok, I think
I do not understand the first question you asked re Full Editor etc. I cannot see this on the forum page
Second question.Nano responds to Arduino IDE upload, so Drivers and Port should be ok, I think
-
- Valued Contributor
- Posts: 168
- Joined: Wed Dec 02, 2020 7:28 pm
- Has thanked: 71 times
- Been thanked: 62 times
Re: License Activation
Full editor and preview refers to the marked button in the picture below.
Once you select it you can use “Attachments” below the text box to add the requested files.
Once you select it you can use “Attachments” below the text box to add the requested files.
Re: License Activation
files attached
- Attachments
-
- TestLED1.h
- (1.82 KiB) Downloaded 17 times
-
- TestLED1.fcfx
- (9.17 KiB) Downloaded 22 times
-
- TestLED1.c
- (3.66 KiB) Downloaded 18 times
-
- Valued Contributor
- Posts: 1207
- Joined: Thu Dec 03, 2020 10:57 am
- Has thanked: 293 times
- Been thanked: 424 times
Re: License Activation
Hi
Sorry to be brief.
Your chart compiles OK for me. Did you download the toolchain / drivers from the Flowcode page?
https://www.flowcode.co.uk/download/
Regards
Sorry to be brief.
Your chart compiles OK for me. Did you download the toolchain / drivers from the Flowcode page?
https://www.flowcode.co.uk/download/
Regards